Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello Team,
We are using custom nRF52833 with nRF21540 (PCB). we manually controlling the nRF21540 FEM using GPIO and SPI (not using the FEM driver) for testing purpose...
Hello
On my application I have noticed that when I use hardware flow control of the uart1 (not the console uart) the processor will get stuck just before the application...
I want to use a hardware encoder to implement a mouse scroll wheel. Do you provide a QEDC routine for me to quickly learn and use? Are there any specific pin requirements...
I've had problems during installation probably due to firewall/proxy/network protection, so I managed to install from command line as specified in Installing the nRF Connect...
I have a couple of questions regarding the operation of the nPM2100 when using the LDO in Ultra-Low Power (ULP) mode, both in active and hibernate states.
Active Mode...
I used the Nordic plugin in VS code to open the process very slowly, and the build is also very slow, it takes a few hours, I have reinstalled VS code, I have also re-downloaded...
When configuring the Bluetooth protocol for NRF5340-CLLA, should I use nrf5340dk/nrf5340/cpuapp/ns or nrf5340dk/nrf5340/cpunet when adding the build configuration, or do I...
When using the nrf52832 to scan and connect to a BLE central device, the first connection is successful. However, after the first connection is disconnected and I attempt...
Hi,
We’re developing a BLE-based product on the nRF54L15 (InsightSIP ISP2454-LX) using nRF Connect SDK v3.0.2 , with MCUboot enabled for DFU.
Our BLE application is based...
I have a custom board using a nrf5340 and am getting a 1 when trying schedule delayble work and I can't figure out why. I isolated the code to test which gets called from...
I recently updated VS Code and regret doing so. My SDK 2.3.0 was working fine for over a year. But VS Code keeps prompting me with an update. I finally updated it and I can...
I want to use the async driver,but did not find the example or explanation.
I have looked for the whole examples with "nrf_libuarte_async.h", found nothing,a little strange...
Hi, The latest version of the NRF connect VScode extension uses forward slashes in paths, which break pristine build on Windows.
The path to my sources has /V in it which...
I want to control RADIO using the TimeSlot API of nRF54L15. I have already created the code for nRF52. However, it seems that RADIO control of nRF54L15 is slightly different...
