Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Okay, I've run into an interesting scenario.
SDK 17.0.2
NRF 52840 (DK)
I am coding a multiperipharal service on a multiperipheral ble device.
My attempt at updating...
Hello,
Does Nordic have a Google Flutter example mobile app for MCUBoot and MCUMgr based DFU (built with nRF Connect SDK) ?
If not, does someone on this forum know about...
We have an nRF52 with dual roles: peripheral for the connection to an app, and central, connecting to multiple third party peripheral devices.
we have a few problems with...
Hi,
I have a problem, I would like to implement a light dimmer endpoint witch I could bind via coordinator to bulb(or something else...). I do not known how to implement...
I am using SDK nRF5_SDK_14.0.0_3bcc1f7 in my project. All the features was working but i need to add the security mode 1 level 4 security in our BLE device with LESC. I have...
want to know how can i judge that the variation is caused in the connection interval, connection supervision timeout, slave latency once i have flashed ble_app_template code...
Hi, Is it possible to estimate the power consumption cost for sending data based on information provided by the modem?
Note from nRF9160 HardwareVerification Guidelines...
I was trying to connect to NRF52-DK using this Python script:
https://github.com/thomasstenersen/pyrtt-viewer/blob/master/pyrtt-viewer
It runs fine on some machines, but...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
Simon posted in this discussion an example of adding a custom service to the...
Dear Members,
I followed the step on :
https://devzone.nordicsemi.com/f/nordic-q-a/71299/getting-hardfault-error-when-using-ble-lesc-pairing/292979#292979
and I got...
Hi,
I'm developing with 52832 DK. I used 'CONFIG_NFCT_PINS_AS_GPIOS' to config pin9, pin10 as general GPIOs and set pin10 to SPI_MOSI. However the system crash when applying...
Hi,
I am creating a BLE communication device (peripheral) using softdevice S132 (v7.0.1) and SDK 16.0.0 on the nRF52832 microcomputer.
I have implemented the BLE communication...
Hello,
I'm new on Nordic environment, I'm designing a RF module that require low latency to transmit few bytes (less than 10) in less then 10ms from a triggering input...
