Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Running 52840 with SDK 15.3, SD140 on SES Ive got an application that has a bootloader on it running DFU. Everything works during DFU correctly but when I get into the application...
Hello,
We are using the nrf52840 with the SDK v17.0.2
We are trying to read specific addresses from our external NVM using the SPIM driver. Unfortunately when we examine...
I had been working with a DK and a Circuit Dojo - nRF9160 Feather https://github.com/circuitdojo/nrf9160-feather just to get my basic hardware working. I just had custom boards...
Hi there,
I've just bought and received Apple iBeacon compatible beacon on eBay ( https://www.ebay.fr/itm/165128797979 ). I put a battery in it, the LED flashes 3 times...
Hello,
Although this topic seems to be trivial and touched many times it seems to be difficult find any ready to use products / projects about it.
The Background
Lets...
SDK Environment: nRF Connect SDK v1.7.1
Target: Decawave DWM1001-DEV. This uses the nRF52832
A 5 byte SPI transfer is taking about 17us when using the nordic spim drivers...
Hi everyone,
I use the nrf52840 and the SDK 16. I copied the saadc example and I want to modify it and use the RTC instead of the timer as an event for PPI. I've noticed...
Hi Team,
I am working with a few Thingy91's. I have noticed an issue in viewing the Thingy91 output on LTE Link monitor for a few Thingy's.
The 1st Thingy connection in...
Hey, I am having trouble setting Pin 0.17 as UART TX. I have tested my code on pins 6,8,15 and 18 as UART TX and the code works. I get the required output on serial. I am...
Hi,
I have been following the webinar "Developing Matter products with nRF Connect SDK" and was successfully able to build the matter lock sample and flash to my nrf52840...
I got PPK2, connected it to Windows 10 PC and it is recognized as "nRF Connect USB CDC COM5". LEDs turn on Grenn color but immediately fade out and becomes red and stays like...
I would to like to update a nrf52833 controller via DFU from another nrf52833 controller via BLE. nrf52833 eval kit is able to connect with another nrf52833 custom controller...
Hi everyone, I am working with nrf 9160 Development Kit. I use LTE LINK MONITOR Unfortunately I am not able to connect to a LTE-NB network. I have updated the Modem Firmware...
I realize that this question will be stupid simple. I can program AVR microcontrollers with no trouble. The setup in the Segger embedded studio seems far more cumbersome....
Hello,
I have nRF52811 project which I would like to transfer to nRF52805. It is using SDK 15.3.
I saw this tutorial: https://devzone.nordicsemi.com/guides/short-range...
