Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I am planning to design a device based on nRF51-dk but with external programmer. I have ST-Link available so I thought I just provide a simple walk through showing...
Hi, all
I tested nRF5_SDK_17.0 ecdh example (path: \examples\crypto\nrf_crypto\ecdh), config with MBEDTLS, CC310, uECC separately and add a gpio toggle to measure timing...
Is there any problem if I stall older version of nrfjprog in my apple Macbook? Will there be any conflict with the new version already installed. The new nrfjprog have the...
Hi,
I'm trying to send and receive scan request/scan response. The system consists of 2 nrf52840, 1 central and 1 peripheral. They both advertise and scan on 1M and coded...
I'm currently working on a program that automates the Legacy DFU procedure and I'm running into some strange issues with writing to the DFU characteristics.
On the nRF Connect...
Hello,
I am trying to use the FDS module with the Softdevices and Peer manager.
I can store some data and I am able to read the header of the record, but when I try to...
Hi,
I want to use the static version of pc-ble-driver in my c++ code. I am learning cmake but I have no expereince with Ninja. I'm using only the version 6 of the API. My...
Target application 1: Data acquisition is carried out for a 0-1khz high-low level signal. The low level is effective. The count is increased by 1 for each trigger. 2: Use...
Excuse me:
I'm developing a keyboard with nrf52832，Calling ble_hids_inp_rep_send() returns BLE_ERROR_GATTS_SYS_ATTR_MISSING when the keyboard is just connected to ipad4...
Hello All,
I am developing a prototype for one of my application.
I am trying to integrate the zigbee stack to my base firmware.
For my application I am using RTC2....
Hi,
I'm using the example "ble_central/ble_app_uart_c" of nRF5_SDK_17.0.2. Connection to peripheral workes fine.
If the central re-starts while a connection is established...
Hello, there
We made a custom tracker device with nRF9160. During prolonged use, we observed that k_delayed_work_submit_to_queue sometime return -22 and cannot be recovered...
When i change the config NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS to 1
the following error comes, how do I overcome this?
<debug> app: nrf_dfu_svci_vector_table_set() ->...
Hello All,
I am facing binding error if I use UART1 for binding but UART0 is working fine. Refer the below error.
Please let me know the solution to solve this error....
