Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
hi ,
I am working on the nrf525832 , i want to store the data which is sent from phone via BLE using nrf toolbox . I tried to merge the flashwrite and ble_app_uart example...
Hi,
I have some questions regarding BLE:
1) What is the max payload size? Where can I find it?
2) What is the throughput in bps? Where can I find it?
3) Where...
Dear Members,
I got the value for cadence, speed and HRM, then display it to LCD,
but after they are all (the input) in 0 value,
LCD is not displaying zero, but still...
Hi,
Recently I am using BLE for transmission on zephyr on nrf52840 When my peripheral establishes a connection with central, the subscription is also successful My peripheral...
The chip runs in the app stage and calls a function to make the chip jump to the bootloader stage (DFU mode).
The SDK we use is nrf5_ SDK_ 15.3.0_ 59ac345,
We made the...
Hello!
I have the NRF9160 DK set up to use UART2 and listen to AT commands from external MCU, NRF52840 DK configured to send using UART0.
The NRF9160 set up is done, pins...
I want to transfer 1000Bytes. if I transfer 1000bytes every second after some time connection broken,
and need to reboot the device and connect it again
how can I solve...
Hi, I get my first experiences with nRF905 modules (module DAYCOM M-FM-NR905 including spring antenna from Pollin) connected to ARDUINO DUEs. SPI communication works fine...
I'm designing a two layer board. I need to route the power supply to several parts while avoiding cutting up the ground plane. I'm consider running the power line on the opposite...
Hello
I'm trying to control the neopixeled WS2812. I referred to the following site.
https://electronut.in/nrf52-i2s-ws2812/
I'm going to use this example of neopixel...
Hi!
I'm developing serial communication programming on nRF52840 DK to get the UARTE1 communication on SDK 12.0.2.
I want to use app_uart_put or NRF_LOG_INFO function via...
I want to develop a device which can communicate with other users without any cellular coverage or network by creating a lora mesh network like above mentioned picture. in...
Hello,
I am having issues integrating mesh functionality into a preexisting BLE project.
My project is based around an nRF53832, with SoftDevice S132 and uses nRF5_SDK_17...
Hi,
i want to connect my nrf5340pdk board with the MPU6050 sensor. They should be communication using I2C.
I read different information about the connection of the sensor...
Hi,
I have two questions about the nRF52DK power consumption when powered via USB .. one is for interest, but the other one appears to be an issue.
I have run some comparative...
