Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi! I would like to power the DK through a external power bank. This leads to led5 blinking rapidly for a while and then turning off. I assume this is because of the debugger...
Hi Team,
We are trying to compile the code with my changes, that changes are normal changes only.
But we are getting below errors in "nrf52840.h" . But we didn't do...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. I'm able to flash my app/bootloader/softdevice...
We are building a sollution using nRF52832. Using the UART over BLE application example as a base we managed to add DFU capabilities to the application etc.
Right now I...
Dear NRF community and support This is a followup question to the DevZone post https://devzone.nordicsemi.com/f/nordic-q-a/2860/flashing-bootloader-and-application-via-j-link...
From everything I know and understand of the system architecture, this shouldn't be possible, but one of our early production units out in the fields has twice now apparently...
I'm designing a two-part computer input device: Part A will communicate with the computer over BLE, but it must also be able to forward along messages from Part B. Here's...
Hi,
I am trying to update the MTU between the central and peripheral to the maximum MTU.
at the connection interrupt from the central side I added
but I got error...
For nRF52832 I see in the datasheet:
I OFF_RAMOFF_GPIO System OFF, No RAM retention, Wake on GPIO,
While for nRF52840 only “System OFF, no RAM retention, wake on reset...
I have an iOS App which is just designed for updating our device firmware OTA. It uses the Nordic DFU library, updated to the latest cocoapod. It connects to our device, and...
Hi,
I use OpenWRT and nRF52832 to develop a BLE gateway, the nRF52832 connected to OenWRT through UART. Now,we need the uart serial DFU of nRF52832, and I found that nrfutil...
I am looking for some advice before diving in to what could be a big waste of time. In my existing Thread implementation, I use nRF52840's in two different configurations...
Hi all!
I am using mesh sdk v4.10 and sdk 16.0 with an nrf52840 custom hardware. I have a question regarding the mesh event handler. I am seeing something weird which I...
I am trying to run DHT sensor on the nrf9160 using the sample provided by zephyr (can be found under zephyr>samples>sensor>dht). The code was meant to run on nrf52. Is there...