Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi, I am evaluating two nRF52832 boards with a PCA10040. I am using the SDK examples Central and Peripheral to talk to each other on Tera Term. I am using the "send file"...
Hi,
We have implemented the reference design of the NRF24L01+. Our tests results in a low range (about 6 meters), we excepted a multiple of that (about 1 kilometer).
I...
We have connected a 50 Ohm Antenna with NRF52832-QFAA-R7, but we tested and found the antenna signal is weak. Could anyone help to provide some proposals for how to improve...
Hi,
I have a STM32 MCU and I want to flash this MCU by using an nRF52840. The two chips will be connected by UART.
From where I need to start, and what is the most easiest...
When attempting to connect to an MQTT broker set up on my local machine using the mqtt simple sample code, I get this output:
What does this error code mean? Also, is...
Hi. We are using the nRF52 sdk v12.1 with S132 v3.0.0 on a nRF52832. Once in a while (could be after running a few hours, could be after running a week) the application ends...
Where can I find the right documentation to start understanding the Nordic Thingy FW? Do we have any design document for this?
I need to develop my own application on the...
Hello,
I'm looking for some general guidance on the following application:
1 nRF52840 based gateway to cloud, on power supply
a few hundred nRF52832 sensor nodes,...
We want to use app_timer_create/app_timer_start to create a periodic timer, but noticed that there were a few seconds missing. After printing out each tick, we see that there...
I can't open my tickets since it's changed into private ticket by your engineer.How can I do?
My ticket' name is"about service change can't receive BLE_GATTS_EVT_WRITE"...
Hi,
I will work with nRF51822. I installed all software tools and I connect target device with debugger.
Should I connect nRF51822 with power like battery (because I will...
I used SES and wrote a printf message at main entrance: when I run in nRF Connect I can see the message that I wrote just after I press the RESET button (OK). Still, as I...
Hi,
What is the GPIO pin state during reset, and during startup ? I have seen that it is a high impedance floating input. How much is the value of this impedance? Can I...
