Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I am having trouble running the ANT+ examples on the 15.3 SDK. I'm testing on a NRF52832 DK (PCA10040) and I'm trying to get the ANT+ examples working on SDK 15.3, in...
Hi everyone
I was testing the bonding with MITM settings. I used the code from the following link: github.com/.../nRF51-ble-peripheral-bond-handling . I tested the bonding...
Is it possible to generate a pre compiled library that configure at run-time new BLE services and characteristics on the nRF52840? If the answer is yes, is it possible to...
Excuse me, I have a question on calling external function.
board using: nrf52832
softdevice using : s132(6.1.1)
The situation: There are two applications which is...
Hi
I am using PCA10040 in order to develop nrf52 firmware. For now I would like to try to measure current consumption.
Is there any couple of pins on the board I can use...
I've been doing some testing with the nRF52840 (I purchased the Raytac MDBT50Q-1M), and I'm seeing a pretty hard startup surge. I've attached the results from my scope. The...
Hello,
I have some problems when running the development kit. It seems the problem might be somewhere on the PCB, something related to power sources and power distribution...
Hello,
I try to make my NRF52832 communicates with a memory (MX25R1635FZUIL0) in SPI.
When I try to read the memory ID, the RX buffer is fill with 0x00. But when I observe...
Am facing issue when am reading data from controller(UART) and using ble_app_uart example code to send data to BLE.
Not able to use two uart's at a time.
My setup: nRF52832 with nRF6707 on top. My embedded application synchronously exchanges UART messages with a desktop application that feeds it data (on demand from embedded...
I use nRF52DK as a central using ble_evt event BLE_GAP_EVT_ADV_REPORT to get RSSI from the peripherals when they are advertising. But once the connection is established, how...
Dear community,
I'm having some trouble configuring and adding subscription addresses to one of my node's Generic On Off Server model. This devices is composed of the usual...
I am new to GATT services and characteristics. I have written one custom service with two characteristics for my custom board. I have used nrf 52832 with sdk 15.2.0 and referred...
Hello,
I am trying to connect to my nRF52832 through J-Link v6.22g. This version doesn't contain the RTT Viewer GUI, but instead I am trying to connect through the RTTLogger...
Hello,
I'm using the nRF52840 in a new design, following the reference designs as a guide. I've noticed that the reference layout files and the development kit use a different...