Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Please help me fix my computer to allow nrfStudio to program pca10056.
I just received 2 pca10056 1.0.0 2018.35.
I am on 2 computers A and B: both with windows 10 64bit...
I trying to debug an interaction between using SPIM3 on the nRF52840 and the BLE stack in the SoftDevice . A reset is happening, which I think is being generated by the SoftDevice...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
Hi nordic.
I use SDK 14.20 and nrf52840 board and s332 softdevice.
Our app has to use ant+ and ble.
My device connect with app.
App requests device to ant+ scanning...
hi guys:
When I was using mesh sdk, there was an error in compiling.
I use examples\light_switch\server\light_switch_server_nrf52832_xxAA_s132_6_0_0.emProject
I am...
Hi,
I am using SDK 14.2 -> BLE peripheral proximity example. I was trying to add a custom service and some characteristics to this proximity example. I basically took the...
Hi, I have two strange problems regarding the NRF_LOG. 1. In a for loop, char string that has changed is not printed out as what it contains now, it is printed out as what...
Hi,
i have purchased the following module
However, after connecting the VCC and GND to 3.3v DC supply the module is not detected. My questions are :-
Does...
how to slove it
1> Linking light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0.elf 1> build/light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0_Debug/obj/ses_nrf52840_Vectors...
I am using the nRF52832.
I want to go to sleep in absolute lowest power mode possible that still allows a timer for wakeup. Using LFINT.
I don't need ram retension, etc...
Code example: nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_ble_uart_freertos
Board: custom board with nRF52840
What are the fastest and easiest steps to make this...
