Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
there is an equation in the code where I see that variable: deviceid is: 229 and var_temp is also: 229.
But the debugging shows that the Mikrocontroller is going...
I'm seeing the same issue as this question , but I'm on SDK 13.1, which has a different peer_manager.c, so I can't directly use the fix for that question.
Like the other...
Hi,
Scenario:
Two nRF52832DK boards on a table, approx 20 cm from each other, +4dBm output power.
Payload length is ~60bytes.
Running at 1Mbps gives me less than...
Hi,
assuming I have an IMU sensor with 3 different interrupt lines. And I want to start a TWI DMA transfer for each interrupt line in parallel. Is this possible since there...
Hi all,
We are starting new project, the aim of the project is control street lights through web site by using gprs connetion.
The key requirements of the project is...
Hi
I finished preparing the nrf52832 board to use ppk and measured it with ppk.
I am trying to repair the nrf52832 board.
However, I do not understand the contents of...
Hello,
I'm porting the nRF8001 SDK to STM32 using HAL (CubeMX). Communication seems to run fine, however, the setup stops with CRC error. See abridged the logical output...
Hello everyone.
I am developing with nRF 52832.
However, when I call UART_init() function. my source code outputs an error message.
source code is under the line...
Hello, i'm using a nRF52840 on a PCA10056 and want to wake up from __WFE() with a minimum delay. When i'm using the debugger, i achieve a low latency but without the debugger...
Hello All,
We are working with one of the customer, where he is asking for range 200 meters between 2 nrf52Dk(nrf52832) and he want us to prove the same using two development...
I am trying to use the cryptocell in the bootloader (bootloader_secure_ble) for verifying dfu packages, but fails in signature verification for the same dfu package, same...
Hello,
I am designing the NRF52832 based board.Specifications of capacitor in reference design is as follows:
0.8pF, NPO, 5% tolerance
But with my vendor these two capacitors...
I am designing nrf52832 based board. In matching, 3.9 nH inductor is given.
I have selected the componenet with following specifications :
Specifications of inductor...
Hi Everyone
I am using nrf52832 development kit , sdk 14.0.0 with iar and i am trying to merge the ble_app_buttonless_dfu and ble_app_uart code.
I have done the changes...
