This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hello! I have a GATT Server in the form of a nrf52840-DK that has been given to me from a company that has a custom service on the server using CCCD. I have the full documentation...
Hello,
I would like to know if using a self made GATT Custom Service in HID Device (NRF Desktop App) can incur additional costs during the Bluetooth qualification process...
Hi,
I am working on a project using the nrf52840. For legacy reasons we are using Nordic SDK version 15.3.0 and SoftDevice S140 version 6.1.1.
I am trying to maximise...
I need help . i am confused that if we send the audio data then it follow which of the following order ? input ->BLOCK ->FRAME->LC3CODEC->SDU->PDU OR input-> BLOCK->FRAME...
We need to establish connections to muliple of our products (they use nRF52832/nRF52840) parallel from our Android/iOS apps to send commands which are time critical (in relation...
Hi,
I am getting an error when trying to enable the Fast Pair (SDK 2.7.0) using the bt_fast_pair_enable() function.
I debugged this error and I saw that it's caused when...
Hi,
I am developing an application which needs a precise reference clock of 20ms. I have a 32MHz Xtal on the PCB with a tolerance of +-10ppm. To configure the device to...
Hi
I'm using nrf toolchain/sdk 2.5.2.
Got a strange problem with my QSPI NOR flash interface. when i run flash_erase i get error message "qspi_nor: Failed to schedule...
I am running a nrf5340 with zigbee as a coordinator, I observed after a while that battery life of my end devices don't last as expected. Then after debugging I found that...
Hi Team,
We are developing a custom board using nRF52840 SoC. We need the storage and handling of IC, reflow solder profile of IC and assembly instructions if any.
Regards...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
hardware:nrf5340+npm1300
software:ncs 2.5.1
hi professor,
If I just connect VBUS, The npm1300 will reset when I read bulk register. If I connect vbat and vbus, read...
In NRFX Oscillator header , accessing the function requires the preprocessor macro which in turn requires preprocessor conditional
The problem is that final conditional...
Hi, I am developing firmware for a project using a custom board with the nrf52832. The project requires mcuboot and secure BT OTA. When I enable the configs
CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I'm trying to send gyro and acceleration values continuously using MPU6050(IMU) sensor through BLE after BLE connection is made with other device.
I took ble_app_uart...
