hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
After I added the device on the Samsung platform, I shared the QR code, and then added it with Apple, but the device could not be found.The log prompt is as follows:
For a project running a BLE connection and sharing data via the NUS service, we have seen that setting up Coded PHY (S2 or S8) will eventually produce an assert error as follows...
How to change Device Information in nRF Cloud? Where do I find the code setting this info? Where is "App Name" and "App Version" defined?
The application is nrf_cloud_multi_service...
I am tring to use this spi bitbang example to write epaper
https://docs.zephyrproject.org/latest/samples/drivers/spi_bitbang/README.html#spi-bitbang
Here is my code
...
Hi,
i want to view the debug logs using the printk function while using the debugger in nrf5340 dk kit. we use RTT viewer to view the debug logs printed using printk function...
I have been trying to:
add MCUBOOT and FOTA to a custom BLE board using the nRF54L15.
I had thought that the sole issue was that the custom board does not utilize...
Hello, I have a minor problem with starting up i2c0 and i2c1. I am trying to run a scanner in the sample code that will print out the addresses connected to these buses. I...
Hi,
I would like to know the best method to force a Public Land Mobile Network Identifier (PLMN). When working with an MVNO , it is very common not to get the right timers...
Hello,
I’m using the GNSS sample (located at C:\ncs\v2.9.0\nrf\samples\cellular\gnss ) to evaluate the GNSS module on our custom PCB, and I need to view its output over...
i am writing an absolutely minimal "bare-metal" application for the nRF54L05 -- one that doesn't use the zephyr kernel or drivers....
all i really need at this time are...
I am trying to use uart21 on nrf54L15-PDK. And I have try some port 1 pins already, and they works well. However, we need to use port2 pin 7 & pin 8 for uart21. But I get...
In my project I am facing issues to send 6000 bytes per second through BLE to androis app
For reading the sensor it is taking 30-40 ms processing time and after that I am...
Hello all, I'm getting stuck on re-installing any SDK and I'm getting the below error. The error:
Failed to clone the repositories: Error: HEAD is now at 100befc70c7 [nrf...
This would be a continuation from a previous discussion on the topic of Bonding information and the process of bonding between the peripheral aka headset and central device...
I am using nRF52 based NINA-112b EVK I saw the spi master example to send the data to slave. Do you have any idea what to do if I want to receive the data from the slave....
