I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode,and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
In the Power Profiler, when I select a larger area in the data logger, then it stops updating the selection time. It works great till 16:40m, but then stays at this value...
I'm working with a DVK that has an nrF52840 with a Sierra Wireless HL7800 modem. The modem is connected physically to UART1 while the UART0 is used for the following as shown...
Hi,
We have developed our code against SDK 2.3.0 and I wanted to try to upgrade the SDK to 2.6.0. I had to remove CONFIG_OPENTHREAD_CHILD_SUPERVISION from my prj.conf, but...
HI
I basically define uart_init(); in Main.
And use DEBUG below to decide whether to use UART.
#ifndef DEBUG
NRF_UART0->TASKS_STOPRX= 1; NRF_UART0->ENABLE =...
In the transition from SDK v2.5.x to v2.6.x, Nordic removed support for boards that don't have the nonsecure (_ns) configuration in the Azure IOT hub sample. In other words...
Hi
I developing a nrf9160 project and try to use FOTA, I reference to example /samples/cellular/nrf_cloud_rest_fota.
finally firmware can successfully downloaded
...
I'm learning to use the Zephyr toolchain and in the interest of connecting the Zephyr-side coding to the i2c protocols I am familiar with, I have some questions.
I'm trying...
I have my software set up so that it does some computation within the Attribute write callback function like this.
b roadcastKeyHandler does somewhat of...
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. The board has an RTC, LSM6DSO as IMU, an opamp front end for the analog inputs...
As title says, I have a clean install of Xubuntu 23.10, latest nrfutil and toolchain-manager package
My shell is zsh, however "nrfutil toolchain-manager launch --shell zsh...
I am looking at the "mesh_shell" example project. I was able to build the sample for nrf5340 dk this way:
- create a new build configuration for "nrf5340dk_nrf5340_cpuapp...
I am working with an IQS572 capacitive touch IC, and when communicating with this IC, the communication window will shut down if it receives a STOP bit.
I am writing a lot...
Dear all,
I am use nrf5340_audio_dk to run the audio_application and I use the BIS mode. I post 2 loggings at the headset device as the broadcast_sink. All things seems...
When I try to build the SDK example WiFi monitoring it showing error, C:/ncs/v2.6.1/nrf/ext/oberon/psa/core/library/check_crypto_config.h:80:2: error: #error "PSA_WANT_ALG_DETERMINISTIC_ECDSA...
As far as I can tell, it is not currently possible to implement the following functionality in a simple way with pynrfjprog across the various device families.
* What is...