I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I need to generate a clean 10kHz sine wave. I tried using PWM ( https://devzone.nordicsemi.com/f/nordic-q-a/89209/clarification-on-how-to-generate-a-10khz-sine-wave-with-pwm...
Hello, I followed this tutorial in order to setup custom BLE service. The tutorial as is works correctly and defines one service with an RX write characteristic and a TX notify...
Hi All,
I have implemented sleep mode in the firmware. I am using NRF52833 in my project. When the device is in idle state it goes in sleep mode. I am able to wakeup my...
I tried adding DFU support to my application by following this official tutorial:
But, I get the following errors:
/opt/nordic/ncs/toolchains/v2.0.0/opt/zephyr-sdk...
We're using sd_flash_write() and sd_flash_page_erase() to store some data to internal NOR FLASH at runtime. We have these calls integrated with the RTOS we're using in a HAL...
I've been using nRF Connect for Desktop a lot recently for power measurements with the PPK2 and to program nRF52840Dongles. I keep stumbling over a small missing feature:...
Hello,
I saw in the documentation for the softdevice s132 v5.10 (which is for production use now), I saw it supports changeable MTU. I have searched for the maximum supported...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hi
I have nrf52833DK it was working all fine but suddenly the LED5 is not lighting up and it is not detected by USB port. I tried to check the board voltage regulators and...
Hello,
I just started working on the nRF52 series controller, I want to upgrade my project using BLE features.
I need 1 master device to send to multiple slave devices...
Hi,
According to CryptoCell-312 documentation , it supports the SHA-1 algorithm. I was able to successfully run the SHA-256 cryptography sample application in the nRF Connect...
In my application, I need to use the nrf52840 for both BLE (as the controller) and ShockBurst. Specifically, it's the nrf52840 on the nrf9160 if it matters. I'm using the...
Hi Team,
We are working on nRF52840 SOC with BLE functionalities.
We need the mechanism for to find out the BLE or BLE Stack is in Hanging state before the processor is...
Hi,
I'm trying to build a proof of concept for a BLE gateway that captures data from BLE sensors and sends it to the cloud via LTE-M connection. I'm hoping that the gateway...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
