Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I want to implement RAI using MQTT, but so far I haven't had success.
I can use RAI without problems through the modem shell, using the command "sock rai -i 0...
Hi Nordic ,
My product is working fine but i'm focusing on improving consumption at maximum because it is working on small battery ( evoluated tpms application)
It uses...
Hi all,
Is anyone aware of any formal documentation or test cases available that demonstrate a validation of nRF Connect for mobile to show that it is reporting the correct...
Hi, I am designing a small PCB (18mm diameter) and would like to know what external components I can exclude for nRF52805/ nRF52811. I would like to not use the decoupling...
Hello,
I am using SES Nordic Edition v5.60 and I would like to be able to include pre-processor directives in my project but I could not find the pre-processor optins. ...
Hi everyone,
I'm wondering on which plateform / app and how is it possible to read and retrieve the data sent from a nRF52833 Slave to a Mobile Phone (Master) ?
We have...
Hello i am working with the example ble_app_uart and i have created one new service and two characteristics. The firmware was working fine with no errors. However my computer...
Hello,
What is the difference between 2 devices which are constantly scanning and 2 devices which are connected? Also, how do I code 2 devices to connect to each other?...
BLE Hello,
In my project i want to send the data from the nrf app to nrf52832 device and i don't know how to interface it with RPI compute module once the data received...
Hello, I have a question.
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral.
I have a question about the output time of the advertisements. The...
Hi,
I am develloping product witch ICM20948 and need to use magnetometer. I tried to move some existing and working code for arduino. I was able to get data from magnetometer...
Hi,
Our customer is optimize the size of flash used of nRF5340.
They are curious whether the definition in autoconfig.h are all used in the image? or some of them are...
I am testing nRF5_SDK_17.1 examples/dfu/secure_bootloader/pca10040_uart_debug
After I run on SES. I got this memory map. It overlaps softdevice area.
With armgcc ...
How do I use printf to output my own messages, and read incoming data, from a UART port that is separate from Zephyr's debugging outputs? This UART line will be connected...
