Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hi I've been trying to get into Nordic's ecosystem using their SoCs but it's been a huge headache. Probably because they don't have their own IDE (like Microchip and STM have...
I have looked at few previous posts regarding integrating ble hid mouse and ble hid keyboard. But of no use, still stuck.
I have seen the following posts already
1) https...
In my device that uses NBIOT I am modifying the FW to use LTEM.
During the tests I have shown that the consumption of LTEM transmission for the same amount of data sent...
Hello, I'm looking for a BLE module with its integrated antenna that works with NRF5340 so far i didn't find something using Nrf5340 other then the UBlox Nora B-106 All the...
In my application I need a reliable BLE link between peripheral (in this case based on a nRF52840) and a PC / Laptop. I need to stream data at a rate of 200kbps with a very...
Hello, I'm working currently on an nrf52805 module and I'm creating a board with it, for now, I managed to do the ble app uart for this module and improve to code a little...
Hi,
we are using the NRF9160 with AWS IoT MQTT. SDK is 1.8.0 and Modem is 1.3.1
Our devices stopped working one day to another (first realized 28.04.2022). The device...
Hi,
I want to know that if it is possible to dynamically update ble advertisement data without stopping the advertisement. (@connectable-advertising)
I would appreciate...
Hello!
I am creating a DFU application and want to customize the bootloader code.
I used this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software...
Hello,
Want to use Segger JLinkExe for flashing the firmware for production. Found that Command Files can be used to automate the flashing process. Also, using "nrfjprog...
I'm actually trying to run the Python CHIP controller in my PC but I got some errors.
I've successfully set up the Open Thread Border Router in a Raspberry PI and I'm using...
Hi
Is there a possibility to read out the actual RX pointer of the DMA if the amount of chars is not reached?
Start Stop the RX is not really an option and I have no...
Hi everyone! I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice. The nrf go studio can not detect the nrf52832, but...
Hi,
I set sending of Ext. ADV at a periodicity of 500ms and scanning for 100% time by setting same interval and window configuration to 2.56 s.
But I observed that the...
