Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Looking for advice on reading data from the BL654 UART RX pin which is getting a text data stream from an STM32 micro.
I tried the "peripheral_uart" sample app in Segger...
When "Zigbee Dongle" is successfully connected and communicated with terminal devices, if the terminal devices that have been successfully connected to the network are all...
Hi there
We are trying to modify the MQTT_Simple example to be able to send more info than the status of pressing a button and having a button pressed notification go back...
Hi, I wanted to merge two example projects: "ble_central/ble_app_uart_c" so I have central client application, and a "peripheral/ble_usbd_ble_uart" so I have working USB CDC...
Hi everyone,
Im working and learning for private project CAN bus sniffer which when receive some data trigger some relay...
I have mcp2515_can hw-184 board on which Im...
Hey all I've had some issues with the zephyr installation and have followed the steps for setting up the toolchain. When im building a project from the command prompt it fails...
Dear Sirs,
In my current project I use nRF52 and external ADC. I have to send 14 Bytes each 500us using UART to PC.
It is only one way connection where nRF52840 is transmitter...
I'm attempting to cause the watchdog timer to timeout and activate for a verification test. I'm using Segger Ozone as my debugger. My OS platform is Windows10. I cannot seem...
I wonder what external load (if any) can be connected to the VDD pin of the nRF52805. Reading the data sheet gives the impression it is for internal loads only, but I assume...
Hi,
Today I realized something interesting for our devices: The Update from an older Software Version build with SDK 1.6.X was on it and I updated via AWS FOTA to new version...
Hi,
I am working on the v1.7.0 and I am trying to connect two peripheral with the same services to a central. The first works without any problems:
When I unplug / disconnect...
Hi
I have been experimenting with ncs recently, just trying different things out.
I'm making an application based on the following example (Which is basically code from...
I would like to add dynamically notify callbacks on a given characteristic.
Currently I can only register one callback on the creation of the characteristic:
How can...
Hello,
I notice that there is a memory region table shown when the program is compiled.
Memory region Used Size Region Size %age Used FLASH: 106392 B 960 KB 10.82% SRAM...
I have a firmware which uses FDS to store configuration, and I want to set some defaults at manufacture. The data might be hundreds of bytes. I could write the data as a binary...
