Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi, I want to create a peripheral device with a nRF52810 module.
Before developing the corresponding mobile app, I would like to use this as a central device: A GUI, written...
I have been trying to get a arduino UNO and arduino Leonardo to communicate with the nRF9160DK but have not been able. That accounts for the SPI example aswell as the I2C...
Given that Zephyr RTOS is not certified for use on Medical Devices, is there any plan to support operating systems with FDA 510(k), IEC 62304, IEC 60601 certifications?
...
I'm looking at augmenting the GPS system of the nRF9160 (at the moment due to high current and long time to acquire, easily lost sats/location) with some geolocation. Specifically...
I met a question here. Hope anybody can help on it, thanks.
I'm evaluating whether it is feasible to run the FFT algorithm on zephyr LTS project, with the nRF52832 board...
I want to know the upgradation process of firmware (Zephyr OS) on nordic nrf52840_pca10056. I have flashed the Zephyr OS on chip once via Jlink/JTAG, and now I want to flash...
Hello,
We are developing a product which includes qr code reading as its feature.with reference to https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo
as...
Dear All,
I need to develop a low-power application that sends a UDP message, waits for a certain amount of time (5 seconds) for a response and if there is no response it...
Hi,
Scenario : Scanning non mesh BLE packet with different stacks.
H/W Device - nRF52DK
Observation :
Case 1. Non Mesh BLE Stack (Soft device):: Here able to receive...
I'm working nrf52 DK, SDK V15.3 , S132 . I have created custom Services and characteristics its working fine. I need to change gap parameter in some cases because i need to...
Dear,
THINGY:91 / nRF91 DK
Currently, Power Saving Mode (PSM) is a feature that is not always available with roaming cards, and we must use the local sim card to use GPS...
It used to be downloadable, but now it's like this
The chip has the old code, and the chip can run the code
Is the chip's sdwio and sdwscl pins broken Or...
Hi,
Now I installed SEGGER Embedded Studio. But I got a activation key from SEGGER. I put the activation key into the IDE. After the I checked in the path "tools->License...
Hi,
I've seen the results of the power profiler, but I'd like to confirm this - with no other concurrent user CPU processes (standby/sleep), is the S132 softdevice guaranteed...
HI ,
I need the nrfutil commands used to generate the following zip file
softdevice only
bootloader only
softdevice + bootloader
softdevice + bootloader + application...
