dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hi,
I recently started upgrading an nRF chip on old SDK to the latest nRF Connect. The device has only one button and currently uses a static passkey (written on the device...
Hi! Firstly I am somewhat new to developing on nordic chips so I'd like to apologise in advance or any silly mistakes or oversights I may have made. I am currently working...
I am using NCS 2.6.1 and have programmed a nrf52840dongle (USB Dongle) with the build result of nrf/samples/openthread/coprocessor
The problem I am having is that normally...
Hello,
I was able to setup nRF5340 Audio DKs as gateway and headset, test the USB audio input and enable the Walkie Talkie demo. But in both cases I'm using I2S/analog headset...
I want to use the signing script as mentioned Technical Documentation (nordicsemi.com) , however, with NCS, this script is not automatically being picked up during the build...
EDIT: I thought I had enabled RTT terminal output in this proejct, which I had not. Obviously this will have an impact on my problems sorrounding RTT terminal output. So I...
Dear all,
I used till now an application to route BLE data over serial port through the dongle USB nrf52840, SEGGER IDE and 1.9.2 nrf conneck. All works well.
Now I'm...
I would like to confirm how to make nRF5340 Audio stereo.
The nRF5340 Audio source is mono, and to make it stereo I believe that it is necessary to convert the data between...
I have a project that was building, but now on restarting VS Code, I cannot access the build configurations.
The list shows a configuration as present, but when I expand...
Hello,
I'm transitioning from the old SDK to the ncs, and have been through the nRF Connect SDK Fundamentals and Bluetooth Low Energy Fundamentals courses.
With pairing...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
