Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
I am using nRF52 based NINA-112b EVK I saw the spi master example to send the data to slave. Do you have any idea what to do if I want to receive the data from the slave....
I am getting an error
warning: SPI_NOR (defined at soc/gaisler/gr716a/Kconfig.defconfig:18, drivers/flash/Kconfig.nor:6) was assigned the value 'y' but got the value ...
Hello,
For a month I have been trying to find a solution to update my devices which are at my customers (these devices have a bootloader, softdevice and app coming from...
Hi
ncs 2.6.1 / toolchain 2.7.0
we have developed a Product using ANNA-B402 (with nRF52833).
Now we made a product variant with nRF52833 WLCSP. Both use the same application...
Hi,
I face a 3mA consumption while I have CONFIG_PM=y and wether or not I have CONFIG_PM_DEVICE=y.
The idle thread is reached and executed :
And the idle thread...
Hi,
Is there a way to make the main thread to execute after any interrupt?
For now, I have something like this (ncs 2.7.0):
in main thread :
In each IRQ handlers...
Hi,
I am sending 20 bytes of data in a beacon format. These are fit into m_beacon_info[2] to m_beacon_info[21] defined in ble_app_uart code from nordic SDK:
I send beacon...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hello All,
I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup,
https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. We have a project using the nrf52840, which is sometimes used by carriers. I ported radio_test to...
Hi
I am using HCI Power Control sample to dynamically control TX power. I found that the TX side's connection RSSI and RX side's are diferent, at some point it even has...
Hello, I'm trying to follow this example (Serial DFU) , on a nRF52840 custom board, but I'm getting the following error:
I couldn't find any relevant information and also...
Hi,
I have recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. To begin, I used the "Hello World" sample code. While I was able to successfully build...
I have searched everywhere and can't find a working example that shows how to create a new BLE ID and save it to the setting s partition.
Please show me the configurations...
We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
