dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi
I could not really find a satisfactory answer to my question, what (if any) impact has the setting of the SLEEPDEEEP bit before calling nrf_pwr_mgmt_run? I'm wondering...
How does the slm routine of ncs1.9.1 use rtt log. Below is my configuration:
With the default configuration, there should be RTT log output, but nothing happens in the...
Dear Nordic Engineers
If we use the NFC Tag of nRF52 series chip.A re there any card readers on the market that can read or write?
Such as ， NXP's NFC tag chip can be...
Hi Nordic,
I am using nRf52833-DK with zephry, an now I'm tring to drive ws2812 led strip.
I notice that there is no nRf52833-DK example in zephyr/samples/drivers/led_ws2812...
Hello,
At the following URL,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support.html
In "The Thread and Zigbee protocols support...
Good Morning people. I'm developing a module with the soic nrf52832 and I'm having doubts about the electrical schematic of the UART communication with another MCU. I analyzed...
Hi
In the old SDK I was able to put manufacturing data into the scan response package using:
ble_advertising_init_t init; ble_advdata_manuf_data_t manuf_data;
and just...
I am migrating to ESB from Gazell to take advantage of the static 252 byte sized payloads. However, there are two things that are very different that I would like to figure...
Hello all,
looking at how to navigate with the nRF tools, hardware amd software.
For example, have designed a bit of applciation with seome peripheral drivers, but I am...
Hello,
I am having trouble communicating with the nRF82532 and the DTM software. I am using nRF5_SDK_17.1.0 which has the DTM firmware. The project that I selected is: direct_test_mode_pca10040...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
#define GPIO_SPEC_AND_COMMA(button_or_led) GPIO_DT_SPEC_GET(button_or_led, gpios),
I find this code in the buttons and led .c file
I tried finding what is does , but...
Hi!
We use the following approach:
If the pin is configured using nrf_gpio_cfg_input we read the pin value via nrf_gpio_pin_read;
If the pin is configured using...
Hi,
I wanted to store a simple integer (the "serial number") by using Setting subsystem of nRF Connect SDK 1.8.0. Settings is based on the internal flash of device (nRF5340...
