Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi
I'm trying to ackquire a GPS fix, and then transmit it to my server as a UDP packet.
First, i enable the GPS with the AT%XSYSTMMODE at command, and then try to enable...
SDK 17_0_2
Hi!
I can't understand is it any possibility to wake up nRF32 from sleep mode via internal RTC timer?
For example- I set ADV duration 30 sec. After that time...
Hi Nordic team !
Is the licencing model linked with the Nordic OTA libraries available in github allows me to freely fork / modify / share a compatible version for Xamarin...
I have define CONFIG_NFCT_PINS_AS_GPIOS, but the pin is always low, even if the OUT register is high.
I have read 0x1000120C(NFCPINS), it is FFFFFFFF, what's wrong with...
Hi, After many attempts I was unable to make RPC_Host sample work ( link to the related nRF Connect SDK doc ). From SES in debugging mode, the network core gets stuck in an...
Hi,
I am writing a program to actively change the state of an LED, then sample the output voltage on the led pin using SAADC, then outputs the adc value to terminal every...
I bought the nRF52840 DK and want to start developing my first application. However, I am very overwhelmed by the documentation here infocenter.nordicsemi.com/index.jsp This...
Hi All, I have a problem with the UART interrupts on the nrf9160dk, the error code (-134 / -ENOTSUP) says that it is not supported. However, I don't know what might be the...
Hello everyone,
I'm unable to perform DFU over SMP BT with nRF Connect for iOS. I've already verified the process works with mcumgr (Ubuntu 20.04 LTS) and with nRF Connect...
I am trying to use the `fmfu_smp_svr` sample project, as described in nRF9160: Full modem firmware update using SMP Server , to perform a full modem firmware update.
The...
Dear ,
I am going to use SDK 17.0.2 spis example.
But I found it is 8 bit data width. I am going to use 16 bit data width .
Would you teach me how to change?
Hi all,
I am using NRF5340, and I want to use pin 0.14 for spim. However, I found it was used by QSPI, in zephry.dts:
So how can I close QSPI to use pin 0.14 freely...
Hi.
Below is used the same schematic for nRF52805 but with different placement for RF components.
What are the pros and cons of each one? Is there one that is "better...
Hi !
I want to successfully send CTE after the CRC of the broadcast packet by operating the RADIO register under the Manual configuration of NRF52833。At present, I can successfully...
