Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello,
I am trying to measure the RSSI value of the Zigbee communikation on nRF5340DK.
Right now I have programmed light_buld into one of the DK and light_switch into...
I have followed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
i WANT TO ADVERTISE the battery...
Hi,
Segger SystemView 3.30 (downloaded from https://www.segger.com/downloads/systemview/ ) does not work with NCS 1.5.1. Upstream Zephyr has updated https://github.com/zephyrproject...
Hi Nordic,
I just had Thingy:91 few days ago. I ran this KIT with thingy91_nbiot_2021-03-04_8e8c6089.hex and asset_tracker example in ncs/nrf/applications . I found that...
I would like to send and receive data to/from nrf52832 pins over BLE using android phone. I would like to capture and display output of Force Sensing resistor and control...
To the kind attention of Nordic support team,
We have got an nRF52833 gzll host that has to interact with multiple gzll devices. We empirically saw that (in our case and...
Hello
I'm using the CLI example as ZC and a custom endnode based on the freeRTOS multisensor example (from nRF5 SDK for Thread and Zigbee v4.1.0). Im trying to send a counter...
Hi, I have a problem with setting up SHELL over RTT. I have managed to get some logs from the device. Prompt `rtt:~$ ` is also shown. but whenever I try to send something...
Hi,
we just uploaded MFW 1.3.0 to our nRF9160 DKs that had engineering revision of nRF9160. They seem to be now bricked and it is not possible to downgrade to MFW 1.2 via...
My task is to create a webserver on the nRF9160DK. For this i'm using the civetweb module provided by zephyr and the ethernet-shield from PHYTEC. I got an issue i want to...
Hi everybody,
I have developed a BLE sensor based on nRF52840 (S140 6.1.1 and SDK 15.3.0) that is normally performing connectable scannable undirected advertising. Since...
Hello,
I need to use the ADC with 600mV internal voltage, ADC Gain stage = 1.
The input signal on VINP vary from 750mV to 1750mV, and input signal on VINN is fixed at...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
Hi, teams.
I checked the operation of nrf mesh network. (mesh sensor example, and light switch example)
It works well. Thank you!
By the way, I have a question....
Hi everyone,
I am having a problem with dfu example. I would like to test my board with the buttonless dfu image, namely
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
