I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi,
I started a project from scratch and I want to write a simple UART printf solution for debugging for my NRF52832 on PCA10040 DK. I know there's a LOG module but it...
I'm working on a BLE peripheral that will connect to both iOS and Android devices. It is important to maintain connection during usage so I consider increasing supervision...
Hi! Are there any existing solutions to send the NRF_LOG output over BLE or to write it straight to a flash/SD-card? If not, would editing the macro's in nrf_log.h be an appropriate...
Hello,
I have a gateway project where I need to receive data from BLE and send on ANT network. As a first step, I took the NUS or ble_app_uart and changed the softdevice...
Dear Members,
I saw ST7735_DC_PIN and ST7735_SS_PIN, which one should I connect to my LCD it has only CS pin ?
ON LCD board ST7735_SCK_PIN 47 --> P1.15 PIN 3 SCK ST7735_MOSI_PIN...
Hello Everyone,
I am using nrf52 dk development board. I'm having a problem when I load my ble_app_uart example . I am getting an error message Error: Flash Download failed...
Hi,
I'm trying to use the nrf52832 as the SPI master to get read/write flash ic MX25L6433FM2I-08G(address - 0x00 to 0xFF).
In loopback case got data but when interfacing...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I get started with Zigbee Door Lock Example in https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/zigbee_multi_dynamic_door_lock_nus_example...
Hi,
We have ordered nr51822 chips in the past. Recently, we made a new purchase and on programming we have discovered that the FICR register information is different for...
Hi Folks,
I am currently implementing a power down routine onto the nRF52840 SoC and I have some questions regarding the right way to configure to system On sleep mode...
Hi,
Is there an example code which can be used to evaluate libuarte while softdevice enabled? I have tried the individual examples in "nRF5_SDK_17.0.2\examples\peripheral...
Hello,
I would like to know what exactly is doing PM_HANDLER_SEC_DELAY_MS and how can affect to the interoperability.
I saw in the bms example (sdk 15.2) it is set to...
The BLE specification says that the CTE can be a maximum of 160us long. I am trying to set CTE length to 160us, but every time i try to do so, firstly the transmitter stops...
Hi Devzone:
We are using J-link pro to collect trace data from nRF52833 DK board, and we found a rather strange behavior:
The sw interrupts would end on its own without...
