Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
I want to control numeric pot (slave) with the nRF52DK (master) with SPI but I'm a beginner in this bus. Do you know where I can found a tutorial or a example (I don...
I'm new to development with the Nordic SDK for the nRF52840 and during evaluation I run into the following problem with the UART ports, which I cannot resolve after hours...
Hi,
I'm looking for a way to access the PDU header data from received BLE advertisements, but I can't find where it is stored. I see that the payload is in p_ble_gap_evt...
Hello every one:
I had modified the light-switch example into a model that can sent and receive multiple bytes.It is work fine when I set the num of bytes less than 10 bytes...
Hi, I have bricked a nrf9160-DK, and was wondering if someone could provide me with a complete firmware image, including secure bootloader, application (AT or Asset tracker...
Hi,
I currently developing my own NRF9160 board Based on NRF9160 DK schematics. My question is, can we remove all passive antenna circuit with all matching network and...
I am using the Fanstel BT840 module with an Epson FC-135 32.7680KA-AC3 crystal and 12pF NPO caps. It functions well in indoor conditions but the LF oscillator stops if placed...
Hi,
I am following this tutorial ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_blinky.html ) to learn how to...
Hello,
I have nrf51822 based Board,
and I need to make Android app for scan and modify Beacon's data.
I found "nRF Beacon" App's source code in GitHub,
and I try...
Hi,
I have seen that there are three most useful topology for mesh : Bluetooth mesh, zigbee and Thread
What parameter should we have to take in consider when selecting...
I'm trying to use a timer with S130, but it doesn't seem to tick:
void timer_event_handler(nrf_timer_event_t event_type, void * p_context) {
NRF_LOG_INFO("Timer 1 interrupt...
Hi,
I recently started experimenting with nRF52840 eval-kits and a nRF52840 dongle using the generic onoff client and server. I used my phone and the nRF Mesh App to offload...
I learning NRF52832 beacon using SDK15.2 i tested code ble_app_beacon code in non connectable beacon mode its working fine. how can i change this code like connectable beacon...
Hey, I would like to add BLE mesh functionality to my existing project which is based on the firmware v2.2.0 https://github.com/NordicSemiconductor/Nordic-Thingy52-FW . I...
I'm planning to connect The nRF52840 MCU GPIO in series to a 1.8V 20mA LED and a Resistor then to ground.
Would the current from the MCU be sufficient to power the LED ...
