Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello There, I want to connect two slaves to my nRF51422 PCA10028. I came up with the idea of using two master communications which share MOSI AND MISO but have different...
Can the chip be updated from an ANT device to a BT Smart Central. This means it starts its life with an S210 and then gets a serial code update to an S120. Obviously with...
Hi,
I'm testing writing and reading at one of my characteristics in Master Control Panel v.3.7.1 (SoftDevice S110 v7.1.0). As shown in the following figure, firstly I've...
Reading from the FICR seems to produce some results other than what I would expect. For example, reading from offset 0x10C seems to return the flash size (instead of 0x110...
Hello everyone
i am using QFAB/DCconcverter reference layout to design my prototype, using the 3V coin cell battery as a power source .my question is in the reference layout...
Hi,
I tart using HID keyboard example, SDK 8.1.
If i turn off the ble of the ios device and then turn it on the nrf51822 is connected but it is not send the chars.
...
Hi, Nordic Engineer:
Would you like to give me some advice? On my hand, i have a slave ble device(not nrf51822, also i can not change the code). I want to run s120 softdevice...
i am able get the status of led of pca10001 board using usb dongle. now i have to make other pca10001 board as central and want the same data of it? Kindly help, i shall b...
We are planning to optimize the radio-frequency signal,so the some docunments like Simulation model are needed.which can help optimize the RF signal through ADS simulation...
In ble_advertising.c, line 165, you can see such interesting code. I assume it is a copy/paste error:
if(p_advdata->p_tx_power_level != NULL)
{
m_advdata.p_tx_power_level...
For the first, impressed by your intoducing NRF52 chip.
Question: what`s NRF52 indoor range using onboard antenna and maximum output power (+4dBm)?
Thanks.
Hi~
I am struggling to get the BLE packets detected by nrf sniffer (v1.0.1) using wire shark. Its only showing "ADV_IND[Malformed Packet]" periodically. I didn't understand...
I believe what I am asking is extremely specific, but keeping hope that I might get some direction
I have used a clone ST- Link v2 programmer to download code into a NRF51822...