Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
nRF52832 + S132 v7.3.0 immediate disconnect reason 0x22 on iPad Pro 12.9 5th gen with iPadOS 26.3 (works fine on Android and iOS 17.7.10 / iPad Pro 10.5)
Content:
Hello...
Hello Nordic Forum,
I ran the Power Profiler Kit on an nRF52DK development board to establish a baseline power consumption.
The current firmware project is quite simple...
Hi,
I am developing a low power BLE device using Promicro nRF52840 boards. After updating to ncs3.2.1 I have noticed a high power consumption in sleep, that isn't present...
Hi! I'm running into a strange issue.
I have inherited this project and it is poorly commented. I have 2 peripherals and 1 central. The 2 peripherals are identical devices...
I am developing a product which uses one nRF5340 Timer in timer mode and another in Counter mode. Reading through the nRF5340 Product Specification v1.6 I have the following...
Hello Support Team,
I am currently working on Channel Sounding with the nRF54L15 devkit, and I am encountering an issue when using main_mode .
Until now, I was using the...
After defining the ADAPTER and initializing UART2 the The adapter pointer fails a test on line 287. FATAL: async_adapter_uart2 points to Flash (0x246d4). Linker Error. This...
Hi, I've tried signing up for a SUPL licence a couple of times but it keeps getting denied. Not sure why. I have logged into devzone.nordicsemi.com and am using the same email...
I’m trying to read/write data to the internal flash of my nRF54L15 SoC using the NVS (Non-Volatile Storage) library.
I successfully flashed the sample nvs application on...
I try to write data into the OTP section of the APP core with the following command line:
nrfjprog.exe -f nrf53 --program 'OTP.ihex'
ouput:
[error] [SeggerBackend] ...
I am trying to program MS12SF1 module through nrf5340DK. I tested the blinky code to toggle the LED pins but while checking through oscilloscope the pins showed nothing, wasn...
nRF54l10 on our custom board in system off has high current consumption, approx 98 uA.
Utilizing the system_off code (C:\ncs\v3.0.2\zephyr\samples\boards\nordic\system_off...
I have got to start with nRF7002-dk and the Wi-Fi sample from the quick start is not working.
I have tried to compile the code on VS code and flash the same code on the...
I would like to estimate the current consumption when the controller is advertising at 2.3Seconds, using external crystal, Tx power of 8dBm, Tx payload of 31 bytes. When I...
We are facing in BLE connection issue in Android phone.
we are planning to use 1. Android phone with 'nRF Connect' for mobile as BLE central. 2. Long range demo applictaion...
