Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode,and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hi,
I have new requirements for nRF52832 using the NRF Connect SDK to develop firmware. I want to know how it supports audio playing with the I2S MAX98357. Is there a possibility...
I am working on a pdm microphone using nrfx pdm driver (INMP621) When I am saving the pcm data into .pcm file using sd card and playing the .pcm file in Audacity I am getting...
I'm using nRF52840 with nRF5_SDK_17.1.0_ddde560, using the ble_app_multirole_lesc example file.
When I set extended = 1 in scan_init , the debug session jumps to NRF_BREAKPOINT_COND...
Hi All,
I flashed an nRF5340 DK board with a samples/bluetooth/hci_uart image and one more nRF5340 Audio DK with a samples/bluetooth/peripheral image.
I have not made...
Hi, I am making BLE low power pult, using nrf52811 chip and NRF Connect SDK v2.3.0.
So, the device is sleeping and waiting for button event
When button is pressed, device...
Hi Sir.
customer want to add FEM for nRF7002, target to extend range around 1.5KM.
please check if nRF7002 can support FEM for this application.
Thanks.
Hello,
I'm new to Nordic and I'm currently learning rust on an nRF7002 DK. I know that the LED0 of the nRF7002 connects to the GPIO1.06 of the nRF5340. However, when importing...
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. I want to send a packet with a notification to my smartphone and then disconnect immediately....
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. I currently implement BLE peripheral for the NRF52832 as it only healthcare sensor data to the...
Hi
We are using the NCS V2.6.99 for a sample project which scans for peripheral devices.
In this sample project, the scan filter (bt_scan_filter_add(BT_SCAN_FILTER_TYPE_UUID...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
Hello,
I have an nrf52833 that interfaces with an external flash module. It is configured to store mcuboot's secondary partition. I am able to write the secondary image...