As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Dear Nordic Support Team,
I am encountering an issue with the nRF52 SDK for Mesh v5.0 and nRF52 SDK v17.0.2 while running the serial example. The system runs for a while...
Hello,
In the header file nrf54l15_types.h, we see the following defines related to the SAADC:
* REFSEL @Bit 12 : Reference control */
#define SAADC_CH_CONFIG_REFSEL_Pos...
Errors on calling "lte_lc_init()"
Does anyone know what the corresponding error codes mean, or what could be done to debug the cause?
Thank you very much.
I am writing an i2s application for the nRF5340 Audio DK with toolchain and nRF Connect SDK v2.9.0.
During development I noticed that nrfx_i2s_start() does not seem to check...
Hi,
I am working on a project where I have two separate physical devices , each based on an nRF52832 :
One device is a BLE Mouse
The other is a BLE Keyboard
My...
Hello, lte_ble_gateway works ok using dk91 or thingy:91 on, v251 - ok v262 - ok but not on, v270 - err v280 - err v290 - err This is straight example code as found in VS....
Hi Team,
I need help currently we are using nrf52833 micro controller, we have problem with external clocks. we want to disable external 32Mhz and 32khz clocks and use only...
I’m using an nRF52840 powered by a coin cell (3V nominal, dropping to 2.3V) and need to read a K-type thermocouple . The challenge is finding an amplifier that:
Operates...
We experience that under some conditions at one moment an already bonded device causes that at the moment of BLE connection the MCU crashes. Possible solution is only to erase...
First of all,I don't study the LOG module yet,just copy & paste from example.
I'm trying to process APP_USBD_CDC_ACM_USER_EVT_RX_DONE event,print debug info to monitor the...
Hello folks,
I'm working on a device that needs a USB storage connection capability. I have put the "mass" sample into my application, and it works as expected except for...
Hi,
we are using the nrf9160 on an addon-pcb as serial LTE-M/NB-IoT modem for our gateway. The host controller is running vanilla Zephyr.
Can someone tell me if I'm wrong...
Hello!
I've been in contact with your sales team in regards to locating the physical BOM of nrf9151, but we've been unable to locate this. I've been - and have directed...
I'm using Segger Embedded Studio. I add some new files in the project. I need to update the directory by right click to Project, then left click at 'Options', then go to ...
