As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I have a question about “Peer Manager” BLE library.
Based on documentation & usage example ( https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.1.0/lib_pm_usage...
Hi,
In previous project, we enable RETARGET flag and include app_uart.h. After uart init we can use printf function to print some debug message very well.
Now, we have...
Hello,
we are currently planning to outfit yet another product with our firmware to make it connectable with our BlueRange mesh ecosystem. Now, I wanted to ask if someone...
Hello, guys.
We are using nRF51822 SoC together with nRF5 v12.3.0 SDK.
According to the nRF51822 memory layout , we have 127KB of space reserved for the Application code...
Hello all,
I followed the Getting Started Assistant for Linux (I'm on Pop OS 22.04 based on Ubuntu). Building with VS-Code and Segger is working.
I want to use Clion...
NCS main
Serial LTE modem does not compile with CONFIG_SLM_START_SLEEP=y in prj.conf
There is missing #include <hal/nrf_reset.h> in main.c but even after including it...
Hello all, I tried installing Segger mebedded studio on a new PC and followed the install steps from the getting started guide. Everything seems to be installed correctly...
Hi there,
we are a student project and are using the nRF51822 Chip with the MDBT40 module. We designed our own custom PCB and followed the instructions for the circuit as...
I have a subroutine that exercises the SPI interface and only at certain points in the code it won't execute the SPI subroutine and goes into the disassembly when single stepping...
SES IDE, nor nrfConnect programmer tool sees the JLink programmer attached to my PC. No "idcode" in SES. No devices appear in Programmer.
Windows10.
JLink_Windows_V764e_x86_64...
Hello,
I am beginner to work with Nordic, I am trying to setup the development environment for nRF5340 Chipset.
For that install nRF Connect Desktop v3.11.0 version. ...
Hi Team
My SES crashed suddenly. When I tick file->nRF Connect SDK Project, It show below error information. I have try to re-install the NCS from toolchain manager. It...
Hi Team,
I have nRF52 DK PCA 10040.
PC: Windows 10 pro
IDE: Keil uVision 5
Working with nRF5 SDK 17.1.0 with S132 soft device .
To execute the code , first i flashed...
Hi,
Zephyr 3.0 , nrf5340 ncs 1.9.1
i can successfully sent data with
this function ;
So it sends 2 transactions without changing cs state.
1byte tx+rx , and...
Hi,Master:
In BT core_v5.0 2.3.5.6.3 Authentication Stage 1 – Passkey Entry, as shown in the figure below
Question: Why does the process loop 20 times, verifying one bit...
