Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello, industry. Two questions for you:
1. To test fault-tolerance of our BLE scanning device we need to generate and advertise from another BLE device custom faulty ...
Hi,
We want to know more about BLE mesh OTA update in Nordic Connect SDK V1.8
Can you please share detail implementation on Firmware Over the air update in NCS 1.8 ...
Hi,
With the latest SDK v 14.2 is it possible to do OTA updates to nRF52 from OSX/Windows/Linux without the use of additional DK? I understand that for iOS and Android...
This might not be the optimal forum for this question, but I'm not sure where else to post it. I have a (I think) very simple question about configuring Zephyr.
I have a...
Hi!
Currently working on a firmware upgrade of nRF91 ns(non-secure) board and build a smp_svr demo from ncs samples found on ncs\v1.7.0\zephyr\samples\subsys\mgmt\mcumgr...
SDK: NCS 1.7.1.
Based on: Peripheral UART example
Central: nRF Dongle
Peripheral: nRF52832
Hi,
I am running into an issue using the "Just Works" pairing method when...
Hi, I was wondering if there is any way to advertise connectable, but non-scannable advertisements.
My device does not have a scan response, but I still see a lot of scan...
Hello,
There is a small problem that I don't know how to solve. I tried looking for it but to no avail. Essentially, my device which runs on NCS v1.7.0 will stop advertising...
Hello,
I am currently trying to record audio using a PDM microphone on the nrf52840 using the nordic PDM library. I have configured the PDM with the default settings, enabled...
nRF52810 SDKs and SoftDevices compatibility matrix does not list nRF52810 SoC revision 2 in the list of compatible SoC revisions for nRF5 SDK. Revision 2 is listed only in...
Hi
I have a machine MacBook Pro 14 Inch 2021
Chip : Apple M1 Pro
I am using nrf52840DK
Using Segger 5.68. installed via Toolchain
Using sdk connect 1.8
The J-Link...
Hello,
We have a head-scratching issue For the sake of brevity, please assume in the following that the definition of "it works" is "the bootloader manages to jump into...
Hi,
I'm trying to interface Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055 sensor with nRF5340 DK board. Can you please help with the code where I want...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
I'm using VS 1.7.1 on Windows 10, with the nrf9160dk_nrf9160_ns
Playing around with myFirstApp from the VS Youtube Tutorials, I wanted to redirect output to uart2 and map...
