dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I'm trying to measure and log the low power coming from a peltier module. (TEG seebeck effect). In Ampere meter mode with LED for load I get nothing. Replace TEG with...
Hi,
I successful developed a application using nrf / zephyr SDK and install the applications on the nrf52840dk and dongle. Now I want to adjust the power using
CONFIG_BT_CTLR_TX_PWR_PLUS_3...
hello i am trying to interface RN8209c ic with nrf52832 using uart communication with sdk 15.2
uint8_t readbuf[50];
uint32_t err_code;
uint8_t buf[10]; buf[0]=0x7f;...
Hi,
I am trying to modify the Android nRF Mesh app to filter un-provisioned devices with URI hash contained on un-provisioned device beacon.
My question is how I can...
Hi
I have a question, the Nordic SDK have a DFU, I want to know what is the default value of TX power in Bootloader? Can we change the TX power? if yes. How to change it...
Hello, I'm using nrf52805. It is confirmed that P0.04 is AIN2 and P0.05 is AIN3. Can I use this pin as UART TX,RX? What should I do to use it? Thank you.
Hi!
I am trying to work through the nRF Connect SDK tutorial series, and I got stuck at the "building with west step" in part1.
When I try to build my project using the...
Hi guys,
I have a peripheral device using a custom service based on the ble_nus, the intention is to hide the service and its characteristics until the bonded has been...
Recently our Device started exhibiting random BLE disconnect problems.
It's really hard to debug as not all of our devices are exhibiting this issue and in generally so...
Hi
I have a question to ask for your help. I'm studying thread networking. The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" I use masterkey networking, but I find it unstable...
Hi all, i want to ensure my antenna have correctly triggered. I'm using TI Boostxl-AoA antenna for nRF52833, Its a antenna of 6 , but i'm just opening up 3 first. my sequence...
I would like to figure our how i can send MQTT packages over a Thread network using a nrf52840DK. And to begin with only between two nrf52840 devices.
I am using the nrf...
Hi
I'm testing RC3 of NRF Connect SDK v1.6 in combination with our application. I have an issue with the configuration when I want to enable CONFIG_LTE_LINK_CONTROL. This...
