dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I am measuring a frequency using the ADC (200ksps) and saving the samples into an array. I save 128 samples then move that data to the fft module to check what the signal...
Currently, debug probes - STLink, JLink, OpenOCD, Black Magic Probe, DAPLinkda, etc. connect to a host PC over a USB, serial or network port and then connect to a target ...
I get ACI_BOND_STATUS_FAILED_ENCRYPTION_KEY_SIZE error when I try to bond my nrf8001 peripheral to my iPhoneX. The min and max key sizes are set to 7 and 16.
Any Idea?
Hi,
I'm using the ble_app_uart example as a starting point for my project. Basically I want to program the nRF52 DK to receive data from another device via UART, store them...
Hi Nordic,
I'm working on a project with very limited board space. I'd like to have the option for both SWD and GPIOs to share the same test points on the board. Ideally...
There is an issue in SDK for Thread & Zigbee 4.1.0 release. It does not appear in previous releases. The problem manifests itself as higher current consumption, as shown in...
I flashed nrf52840 usb dongle via SWD and now it can't go to DFU mode even if I press reset.
Green and blue leds are constantly blinking. How can I go to DFU mode in that...
Hi all,
I am developing ADC functions with Mynewt on nrf52 DK PCA10040 board.
The working example code based on SAADC driver nrfx 1.7.0 won't work on nrfx 2.1.0.
Example...
Hi Devzone:
I have been testing flash storage project.
in my code I have declared a one page flash at 0x40000 for my own use:
And in flash_placement.xml I have inserted...
I must be doing something obviously wrong but I just can't see it.
I'm trying to create a PPI linkage between the UART RXDRDY event and a timer working in counter mode so...
hello
i am working with nrf52832, s132, sdk 16.0
i am trying to init 3 channels with OVERSUMPELING and BURST enabled:
"
nrf_drv_saadc_config_t saadc_config;
...
Hi. I need to use some of the flash on the nRF9160 for non-volatile storage. But I want to do it in a very specific way to save on RAM usage.
Essentially I want to be...
i want to configure MAGPIO0 (GPIOTE) pin as a output pin.
But its configuration is different from normal GPIO pin, so please guid me that what is process and configuration...
