S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hi,
I was writing a program that uses the PPI with event from the timer and the task to one of the GPIO pins. The ideal scenario is that, whenever the timer fires, it...
I am currently experimenting the the nRF52 DK and the CSCS Peripheral example.
The provided example from the SDK creates random values for cycling speed and cadence, i.e...
I'm trying to make the sample beacon in my custom nrf52832 board, builded by Segger Embedded Studio.
The code runs fine when I'm connected to the device with the OpenOCD...
Hi,
I have an application that is mainly uart based and uses the app_scheduler, libuarte, cryptocell and pwr_manager. I want to introduce the Softdevice, and the first thing...
Hello,
I am testing the PCA10040 example project & modifying.
I was checked that the project works well in nRF52832 board.
Now, I want to download the project to nRF52810...
Hi,
I am using nRF 52 DK as a sniffer and monitoring the BLE traffic on Wireshark. The goal of this is to ensure that the communication is encrypted.
I can see that in...
I tested "ble_app_buttonless_dfu" example and "ble_app_beacon" example. Everything was fine. Now, I am trying to make an application that advertise as a beacon and supports...
Im trying to come up with a commercial low power sensor module using the nRF91 DK. What happens if i use my own Telstra SIM card, will it have access to NB-IOT in South Australia...
I use Android nRF Toolbox Uart and NRF52832（SDK version ：17.0.2，app：ble_app_uart）。
I set （RX＆TX）PHY 2M，（11.25-15,0,20S）。
form NRF52832 send data to Android nRF Toolbox...
Hi guys
I try to develope a bluetooth application with a customboard on Zephyr 2.4. At the moment the firmware should work on the nrf5340-pdk until the hardware is ready...
Hello NordicSemi,
We are developping a product based on the nRF52840-QIAA and are using the schematic reference nRF52840 DK Hardware files which is similar to the circuit...
I have developped an application using bluetooth mesh with NFC to read a text record. I am currently using the nRF52840 DK Rev 2.0.1 2020.11.
Regarding my software setup...
W e have the problem with GPS that it sometimes takes a long time after a cold start until the modem gets a fix. I see strongly fluctuating times between 78 s and> 600 s ...
I'm trying to modify the asset tracker for the Thingy91 to read the actual values of the ADXL362 and BME680 sensors. By default for some reason the project uses simulated...
Hi,
this project is upgraded from 51422, now use 52832, sdk 15.3 and sd332, we encounterd a issue that the ant burst always fail after first segment is sent while ble is...
