Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi, I'm using my own custom board.
MCU : NordicSemi nRF51822-QFAA
SDK version : 7.2 (I use IAR 7.1 for ARM.)
Softdevice : S110 7.1
Each 3 examples does work with...
i am sending data with the advertising, and the Dongle receives the data. It only receives the data at certain times. 20 sec receiving, 30 senconds nothing...and so on.
...
Good afternoon,
I want to get date and time from the RTC1 and working on the S110.
As the RTC1 counter is just 24-bit long, final counter value (overflow) has to be taken...
Anyone had any success get uCXpresso.NRF working with the latest nRF51 Dongle. I can't seem to get the BLE stack working.
Trying to run this example but the device is not...
Just starting the external LFCLK needs a considerable amount of energy. With my evaluation board it takes about 340ms for the XTAL to get started, which is well within the...
I am only interested in one max bonded device at the moment so I want to replace the old bond with a new bond. Is there an easy way to do this? I only want to replace the...
Hi,
I am try to manage situation when a wrong PIN code is provided from Master control Panel.
Using an NRF51822 with S110 I receive this code:
BLE_GAP_SEC_STATUS_CONFIRM_VALUE...
Hi,
I'm trying to communicate between a stm32f4 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1
My application has no display, and a single button for input. I want to prevent bonding until the button is pressed...
I use Eclipse, gcc and OS X to compile.
I had FW working just fine with SD 6 and SDK 5.2. I recently tried to upgrade and ran into many problems, but the latest is the...
Hi
I've written an application that uses the gazell proprietary stack for nrf51822 and I want to use OTA-DFU using BLE.
Is it possible to upload the new firmware using...
I’m running into a problem with the SoftDevice safe twi that’s been posted in the forums a few times. I got the file here:
devzone.nordicsemi.com/.../
One of my peripherals...
Hello,
I have been messing around with a PCA10001 Dev board trying to do some power consumption tests (Beacon demo code). When I enable RTC1 only and use __WFE in the main...
