I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi,
I developed application whitch is using S130 soft device. On central side to manage devices, i've used device manager from sdk 6.1.0. It works fine.
But now i need...
I tried to upload application through BLE DFU in MCP. The DFU Android app works fine. However, it always failed in MCP.
SDK 6.1.0
SoftDevice 7.1.0
MCP 3.7.1.8567...
Hi,
I have following use case. The write operation on one of the characteristics triggers some UART job which takes about 1 / 1.5 seconds to complete. After the completion...
Hello,
I try to use the S310 V2 but got stuck into problems.
in order to start the application from bootloader in the S310 V1 I did succesfully :
void (*application...
Hi,
I have problem on compiling bootloader example which is located at
\Nordic\nrf51822\Board\nrf6310\device_firmware_updates\bootloader
When I try to compile the...
Hi,
Some questions in example ble_app_hids_keyboard/main.c
Why set the adv_params.timeout to zero in BLE_DIRECT_ADV (Line 779) ?
That will cause no BLE_GAP_EVT_TIMEOUT...
I just got a nRF51 and am having trouble getting started with it. I created a very simple program using the mbed compiler and produced a hex file which I now wish to flash...
Hello,
I see that the make files that have been included have provision to remove dead code from the projects to reduce code food print. This is accomplished using the...
HI folks,
I have checked the current consumption while connected on an average to be 325uA (with uC taking 4.5uA) so this mean almost 320uA being consumed by the nrf8001...
I have a general question about the RF frequency tolerance of Nordic devices in general. Is the following calculation correct?
Crystal spec = 16MHz, +/-50ppm tolerance...
Are there any plans to add boundary scan functionality to assist ICT testing? If not, are there any other hooks into the part that can be used to test during ICT?
Hello
I'm using a pstorage_register from pstorage.c to register two application storage blocks in flash memory. But I have situation that first module have 6 blocks of...
Hi,
are the GPIO pins broken out on the nRF51 Dongle configurable and can be used for SPI Slave tests? I have a running system powered by a ARM Cortex 4 (Teensy 3.1) and...
We have an early implementation of the v6 SDK DFU ported to support S310 on a handful of devices in the field and need to update them to a new bootloader and we'd like to...
