Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello everyone, I'm trying to perform a device firmware update using the buttonless service on nRF52DK with SDK v17.1.0 and Softdevice S132.
I can connect correctly to my...
Hi,
I’m working with Timer 0 on my nRF5340 DK and trying to set up two different intervals: one at 1 second and another at 60 seconds, each on separate channels (COMPARE0...
If I am to do a custom SPI Slave driver to achieve ultra low latency handling and would like it to coexist with NCS / Zephyr, is there a document describing this ?
E.g....
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it is iBASIS...
Dear ESB technical specialist
Regarding the ESB function of nRf52833.
The datasheet explains BLE function, but there is no explanation about ESB.
For this reason,...
Hello,
We are using the nRF52832 in our product, along with nRF Connect version 2.6.0.
We have been working on obtaining Bluetooth certification, but we encountered issues...
As I understand it, the nrf samplesaws_iot and aws_iot_mqtt assume there a network connection up and running.
I am trying to adapt the sample to create the connection via...
Hello,
The target MCU on nRF5340 DK seems to use internal load caps for the high frequency 32MHz XTAL because the board does not have external load caps.
The nRF5340 specification...
Hi,
While I understand that the sample code is not intended for the nRF52 Dongle, I am still wondering if I can make it work on it.
I have successfully tested it on...
Subject: Request for Assistance: Coding BLE and SPI for Gesture Control using nRF52840
Dear nRF Support Team,
I hope this email finds you well. My name is sharon and I...
Is there any analog to digital input on the nRF9061 SiP / DK? I essentially need to plug in a microphone to this, so I looked at a couple of options -- ADC, the DMIC interface...
Hi,
I'm using an nRF9160DK v1.0.1 (2021.26) for developing an application on the nRF9160 with ncs v2.5.0 and I'm currently looking to optimize current consumption. I realize...
In my project, my master controller need to scan devices through custom uuid.
One problem is that in ble_advertising_init, I can only add 16bits uuid and type of which is...
We need to issue a command to an nrf52840 device :
nrfjprog --program file.hex --chiperase --verify.
everithing is working with [nrf-command-line-tools-10.24.2-x64.exe...
