Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
When I use the command to read the software version, the message read by the Raspberry Pi does not appear " SoftwareVersion ".
Please confirm the attached LOG message
Hello,
I have a question about performing OTA via BLE (SMP) and using BLE mesh. Is it possible to perform OTA via BLE to ZigBee network and vice versa.
Since BLE is supported...
Hello,
I'm encountering issues while trying to install and update the nRF Connect SDK (NCS) environment on my macOS system.
NCS versions attempted: 2.2.0, 2.6.1
...
I am using nrf52840 to test the `periodic_adv_rsp` sample application using ncs. I had this use case where I would like to configure data in a subevent based on responses...
Hi Nordic community,
I'm starting this course as I'd like to start with Nordic.
I can't continue (better to say, start) the course as the instructions are different from...
Hello, I have an eval board of " nPM1100-EK -> PCA10123 0.8.0 " battery of li-po 3.7v 600mah battery termination voltage is 4.2V The above eval board works fine & the battery...
Greetings,
I'm trying to migrate the MAKEFILE configuration to SEGGER studio so that I could build and debug the project from there. So far, I'm stuck on the Linking part...
We are currently working on a Zigbee-based network coordinator using the nRF52840. I have a function, dfu_multi_image_write , that writes data to NVS in chunks. The function...
The Power Profiler app v4.2.0 release notes say:
"Updated PPK2 firmware to v1.2.0, which adds COM port for shell access"
Are there any instructions available how to use...
Hi,
My application is running NCS v2.5.3 on a nRF5340.
My project has FOTA via BLE, is running mcuboot, and is a multi-image build. I am trying to verify, from within...
Hello, I am trying to subscribe on a topic to get retained message.
I am using ncs 2.7.0
The problem is that whenever I am trying to subscribe to a certain topic, I have...
Dear all,
For a project we need to synchronize up to 5 data loggers, each of them is based on nRF52840. The sampling rate of some sensors can be of 1 kHz. I'm wondering...
Hi All,
I am lookging for a way to use the nRF7002 (or other 2.4 GHZ WifI solution) as a WiFi sniffer.
I want the solution to provide, for each WiFi packets in the previously...
my nRF52840 has MBR, SoftDevice, Application and Bootloader.
Can Bootloader call API in SD?
Will it be an issue? If I need to upgrade SD (could be a newer version),...
