Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi,
The nRF document describes that the maximum length for advertisement data is 1650 bytes, but extended advertisement support only 255 bytes by default
Is it possible...
Hi,
I have an nrf9160dk which is not modified in any way as far as I can tell. I am not sure exactly which hardware revision (it just says 1.0.0 on the label), but it...
I'm trying to use the LVGL module inside zephyr, however, it requires specifying the zephyr,display driver in the device tree.
The zephyr sdk contains drivers for the FT81xx...
I am doing mcuboot using stm nucleo board through nrf connect . i am using blinky application for build but i got some error .please tell as early as possible
Building...
Hi, I am using the ZBOSS NCP production ready firmware from NCS v2.0 and I have some issue with serial communication.
I am able to run my application, and I don't have any...
HI ,
I am using west tool to build and flash the example . as I have tried this example (Nordic\v1.9.1\bootloader\mcuboot\samples\zephyr\hello world) , which is not working...
The version of bootload I use is as follows:
，Finally, the file was synthesized by NRFUtil and downloaded to 52840. The system started well when it was powered on, which...
Hello all, We 're working on our custom PCB prototype. We can see current consumption according to this profile even though the flash memory was erased. Also the modem FW...
Hello all,
I have started to port the code from the nRF52dk in Segger EM, indeed, everything so far works on the NRF52 dk , so I have opened the Blinky example for the nRF52820...
Hi,
I am using an nrf52 DK and facing an issue regarding the GPIO voltage levels. The GPIO voltage is around ~2.35V when its in LOW state and slightly increases when in...
Hi,
like mentioned in the caption, i have updated the nRF Connect SDK version from 2.0.0 to 2.0.2 and noticed, that the debugging does not longer work as expected and before...
Hello, I plugged in the nRF52840 dk and LED1 fades in and out. It does not blink. I am unable to connect to my phone. I tried to drag and drop some hex files to the JLINK...
Using the Power Profiler Kit II with
nRF Connect for Desktop (v 3.11.1) on Ubuntu 20.04 with the Power Profiler App v3.4.3
I'm wondering about the value of the time axis...
When operating in high-voltage mode, the spec says that VREGH,DROP is at most 0.3V . What happens if VDDH falls below the programmed VDD output plus VREGH,DROP, for both the...
