Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I'm unsure if this is the correct place to post since this is not a Nordic-specific issue.
I am using the P100 which is a nrf52840 connected to an HL7800 through a UART...
hi all
i want to use a chip antenna for nrf52840
but un data sheet there is not any sample layout or component details
for example i want to use this chip antenna
...
Subject: Query: Interfacing OLED SSD1306 with nRF52832 on Zephyr
Dear Zephyr Dev Zone Community,
I hope this message finds you well. I am currently working on a project...
Hello! The S140 7.3.0 SoftDevice docs say it requires 0x27000 of flash, but the SoftDevice hex only occupies 0x26634 bytes. This leaves 2508 bytes of hopefully unused flash...
Hello, I'm trying to confirm whether the front-end module (FEM) is actually active in my application. Here is a summary of what I have done so far:
Updated prj.conf...
I followed the example described in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_nrf52_developing.html#fota-updates
and the loaded the SMP Server example...
Hallo,
currently I test several options in regarding the use of advertising. I have a few nRF52840-DK and use Zephyr 2.7-99 and ncs. I have a question regarding combined...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
In our application, we provide internet connectivity to the WT02C40C module via a mobile...
Hi,
I have a makefile generating an elf and then a hex and bin file for a nrf52 project. Now I builded up a zip file for bootloading. Which works as well.
Now in our CI...
We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
I want change toolchains, so when i open nrfconnect terminal I can use my own west command. I've read link , link and link
Option in the picture lets me install or open...
Hi,
There were GPIO /SPI Interface headers are given on NRF21540 EK .now how we can connect RF input to TRX pin of NRF21540.
please provide the Understanding of RF input...
