Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Dear all; I am an originally signal processing expert working on "positioning in smart cities" for IoT using bluetooth 5.1. As part of our new tasks, we are to evaluate the...
I have several nrf52832 based (similar) devices, all are programmed once (at least), now when i try to update program some of devices cannot be programmed (about 5...10% of...
we make the tracking system. so, we want to measure the voltage of li-po battery (i am using nrf51 sensor tag with li-po battery), so, their is any circuitry or any API or...
Hi!
Program enters infinite loop in `sd_ble_gap_adv_start`.
Setup: I've seen https://devzone.nordicsemi.com/f/nordic-q-a/11818/sd_ble_gap_adv_start-hangs-after-disconnect...
Hello,
I've been trying to get a Thingy:91 to connect to the nRF Cloud from Shenzhen, China.
The modem is updated to mfwnrf9160120 and the firmware is on thingy91_nbiot_dfu_2020...
Hello,
I Have a custom PCB with Fanstel BT832 module soldered. Because that module does not have a 32 KHz quartz I need to set use the internal RC source instead. The problem...
Hello,
I am trying to understand if I am able to use the SPI pins as GPIO when SPI is not being used. This post says that we could be able to use I2C and SPI pins besides...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
am use SPIM . I...
I have an issue in buttonless dfu,I have 2 kinds of device,one has issue in dfu,another one has buttonless dfu and works well, I transported DFU code form another kind of...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am in the process of RF certification.
I downloaded the example at "nRF5_SDK_16.0.0_98a08e2...
I tried in vain to connect my nRF51822 eval board with LIS3DH using SPI. Currently I am using the SPI example in PCA10001 with spi_master_init and spi_master_tx_rx function...
Is there an issue with my clock that's causing the BLE not to advertise? The debugger seems to an error on the gatt_params_init() function, which should mean its a RAM address...
Dear BLE mesh Experts, We want to provision and operate a mesh network using an app that is running on various phones. The idea is to use a single phone during installation...
hi Forum. I'm working on a project with nrf52840 + S140 + TWI (SDK v16). Got all working separatly on my custom board, i.e. softdevice alone works fine and TWI also works...
Hi,
I'm trying to implement Install Codes on our project without good results: The end device could not join the coordinator network after retrying several times.
Because...
