Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I am using an nRF52DK kit, SDK V11.0.0 and SoftDevice S132 V2.0.0. I have found an advertising example on the site github.com/.../nrf51-ble-tutorial-advertising . I have modified...
Hi,
We made a custom PCB using the NRF52832. We have connected a button to P0.21 which is the reset pin. We have configured this button as input and set the preprocessor...
Hi,
I am using multiperipheral configuration. I want a characteristic to be read by only a specific peer among connected peers. How do i recognize and authorize this specific...
Hello is a starter developer
I used the nrf51822 chip on the pcb board and downloaded the example code but it did not work.
When I checked the 16mhz external crystal on...
Hi all!
I´m trying to use FDS to read and write to my nRF51 using the example from Infocenter.
The write seems to be OK and returns 0x00.
But fds_record_find() returns...
Hi everyone.
I want to add RFX2411N to extend BLE signal coverage. I also need to minimize power consumption. I used VDD_PA to control TXEN and 2 gpios control both TXEN...
Hi,
I am testing the USB CDC ACM Secure DFU Bootloader example via NRF52840.
softdeivce uses 5.0.0-2 alpha and uses SDK version 14.1.
I have a problem.
I ran Erase...
Hi,
I need to activate one pin just before the sample is taken on a saadc channel. I have settings as in saadc example.
How can I do this? Is there any event that I...
Is it possible to send more than 255 bytes on SPI when nrf52832 is used as slave. A few solutions use SPI Master with easyDMA and ArrayList to do this. Will the same solution...
Hello,
I have a question is it possible to break the nrf52832 if I try to load the application when the UART of the module is active(TX and RX pins are 1).
The softdevice...
Context :
I am using a nrf52832 to communicate via UART to a STM32 on a custom board. I've based my work on the Ble nus service example.
Main change from the DK is that...
I am playing with example app from this tutorial devzone.nordicsemi.com/.../
I can see the app only when I start debugging. If I just power up my custom board, it doesn...
nRF52, S132, SDK13.
I need flash two .hex files. One- firmware, second- data. It flashed on a factory. data- veans serial number and other personal chips info. Now I can...
We want to flash ble_peripheral over nrf52. How can we proceed?
we use the code from following link when we try compile this code in segger studio we get following errors...
I am using keil 5, softdevice 132, sdk NRF_SD_BLE_API_VERSION=5, nRF52832.
I am trying to work with firmware update over ble.
In the example folder, there is an example...
