Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
Two month ago I have test nRF21540 and nRF54L15, they cannot word with each other.
However, I notice these days updated with
https://docs.nordicsemi.com/bundle...
Hello,
I am trying to use the nRF21540 in nRF54L15, I notice document metion
I am wondering what is the difference between PPIB and DPPIC. What does appropriate...
hello, I encountered a problem using SPIS to communicate on nrf54l15
Environment: NRF54L15, NCS2.8.0
When using SPIS for SPI communication, you must first write empty...
We are using nRF Connect SDK 2.9.1, Zephyr. The hardware used is a nrf52840dk, rev2.
We have a proprietary protocol that is running concurrently with BLE and uses MPSL API...
Hi everyone
I am using the nRF9160 DK board with the VS nRF Connect extension. I am stuck at lesson 7 exercise 1 of the Cellular IoT Fundamentals lesson.
Up to this lesson...
hi support team,
i want running chat demo in mesh fold in ncs2.9.0, but it doesn't support thingy53 natively. so i ported some of the file from light to chat demo. you can...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hi! I have been developing a GATTClient and GATTServer on two separate nrf52840dk boards and have been doing so for a long time.
This Friday I got everything to work when...
Hi Nordic Team,
I'm currently working on a BLE project using NCS v2.9 and targeting a custom board based on the nRF54L15. My goal is to use the SYNTH LFCLK source (instead...
Hi Nordic Team,
I'm facing an issue with BLE communication on my custom board using NCS v2.9. I started from one of the standard SDK examples (like throughput or peripheral...
Hi,
I just got a PPK2, I'm going to measure the current of a nrf52 custom board, which is supply with Li-ion battery.
Should I connect GND on PPK2 to battery(-) when I...
Hello,
I am debugging in an environment using BLE with nRF54, but after breaking, when I step through it, the debugger stops and I am having trouble.
The environment...
Hi Nordic team,
I'm working with the nrf5340_audio source code from the nRF Connect SDK and have compiled the project as a gateway. When I try to connect to a headset, I...
