I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
I have an external flash
S25FL132K
I am able to read , write and erase the flash with nrfx_qspi_cinstr_xfer function for 9 bytes. But I want to write more than 9 bytes...
Hi all, I am working on an electronic lock using the nRF52840. Currently it works using Bluetooth Low Energy and the lock opens when a digital key has been sent. (it has measures...
Hello sir,
I am sending the data of 252 bytes through send_notification() at each interval of time but when i send through send_notification() then following error occurs...
Hi,
I am compiling micropython port for Thingy:52. I am following instructions here https://github.com/micropython/micropython/blob/master/ports/nrf/README.md
I see that...
Hi,
I have created an HSL model and it's working fine. Now, I am using a light that has both CCT and RGB control. So, I have both HSL and CTL model existing in the same...
Board ：52840dk_52840
SDK： NCS1.7.1
IDE ：Visual Studio Code
I remap my bootloader partition in my application .overlay file
as
& boot_partition {
reg = < 0x000000000...
Hi,
When i changed NRF_LOG_ENABLED from 0 to 1 in file sdk_config.h returns the following error
1> Linking tdoa_tag.elf 1> E:/gcc/arm-none-eabi/bin/ld: Output/Debug/Obj...
Hello, did you test the working of 100 pairs (Transmitter and Receiver) nrf52840 BLE modules together indoors? If you did, how much data is lost while working together? Can...
Hi everyone,
I use the radio example as my basis. I call the read_packet() function from receiver example. And there is no incoming data, it stucks there. How can i set...
Hey,
I have an app based on the UART central example. I successfully connect and bond to an android and am able to send data via uart over BLE.
I want to send data also...
Hi
I am converting libraries MAX30105 Arduino to nRF52840, but I have a problem,
"MAX30105 parrticleSensor;" what is it?, how can I to convert this? is it a variable?...
Hello , I am trying to build the bootloader source code provided by Adafruit for its nRF52 core. The project is based in Segger Embedded Studio.
Adafruit's nRF52 core bootloader...
Hi,
1. I removed RTT related codes in the project.
2. Will uncontrollable factors be introduced?
3. Is there any potential risk when the code runs?
Thank you for all...
Hello,
Trying to run the TWI_SCANNER example on a pca10100 hard faults. The .emProject file has been modified per the instructions at https://devzone.nordicsemi.com/f/nordic...
