Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
I am writing a basic health device application, It starts, loads saved data, starts advertising, takes measurements, if a connection occurs the data is transferred, other...
I have compiled the example application ncs\v1.4.0\zephyr\samples\boards\nrf\system_off configured for the nRF52dk_nRF52832
This example consumes 450-500uA (SB9 cut)......
Hello Nordic support team,
We are making product relate to battery service.
Tool and SDK: - nRF5_SDK_17.0.2_d674dde
- SEGGER Embedded Studio for ARM Release 4.52c
...
Hi, I am doing some development in nrf52810. where i want to use BUZZER to produce TONES
I am using SDK17.0.2 SES
I want to create tones instead of just beep sound in...
I found a fairly cheap (<$5) FCC certified NRF24 module with 20dBm output power. NiceRF RF2401F20 ( https://www.nicerf.com//product_180_216.html )
The FCC ID is 2AD66-RF2401F20...
Hi,
I would like to know security related libraries available in SDK 17.02.
Libraries that I found
1. Peer manager
2.crypto library
I would like to know is there...
Hi,
I got problem with Implementing the FDS example code as below, which I using is SDK nRF5_SDK_17.0.2, and always got error "FDS_ERR_UNALIGNED_ADDR", Already searched...
nrf5 SDK 15.20
Mesh SDK 3.0.0
nRF52832
Hi,
I am using nRF52832 and mesh stack , i want deliver temperature data through Mesh network.I look and run light-onoff &...
Hi Folks,
I would like to configure an UART RX pin as input GPIO as well as keeping it as dedicated to the UART peripheral.
I would also like to know if I can configure...
Using the current nRF connect v3.6.1 Getting Started Assistant I've managed to get everything installed to the point of using west to install the complete nRF Connect SDK...
This thread discusses the nrf51 devzone.nordicsemi.com/.../current-consumption-when-using-rtc-ppi-and-gpiote It says that the PPI (for nrf51 chip revisions up to rev 3) keeps...
Hi,
What is the used coding scheme in nRF Connect for Mobile when advertising on Coded PHY? Is it S2 or S8?
Should be clarified in the screen below
Thanks,
Lu...
In this PDF: https://infocenter.nordicsemi.com/pdf/nwp_037.pdf
On page 28 it says:
Active components on the PCB cause wideband noise coupling to the antennas. Verify that...
We have designed a board using the nRF9160 SiP and LWM2M. When testing with poor network connection (~ -118dB) we experience a strange behaviour. From monitoring the current...
