Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hi All,
My team recently reserved a custom service UUID with the Bluetooth SIG, and we'd like to replace the custom 128-bit UUID we had been using in our products. Can I...
HI
We are mass producing NUS-based products.
During mass production testing, pairing is performed and functionality is tested by pressing buttons, etc.
However, pairing...
I'm using
AT_MONITOR ( catch_all , ANY , on_modem_at_notification );
and I'm just printing the notification on reception:
static void on_modem_at_notification...
Hello,
I would like to add to my project new i2c slave (for example - dac5571 from TI). In the DTS overlay - under the i2c0 node I need to specify compatible , and I don...
I have configured the nrf52840 DK one board as Peripheral and other as central.
Added multiple services and characteristics. I am sending some data at every 20ms using notify...
Dear all:
Customer products in normal mode, BLE works normally, all functions are OK. An error occurred in DTM mode during authentication. Procedure The failure status is...
Using the SDK 15.0.0 SPI example (master) to send a single byte.
Sending 0x00:
Sending 0x01:
Sending 0x02:
Sending 0x04:
etc ...
Sending 0x7F:
In all the...
I am working on a module MS12SF1(nrf7002 + nrf5340) module. I am getting uart data from another device to this device through uart. Earlier when I configured uart to its by...
We have some custom hardware that acts as a peripheral, and currently has the advertising data packet set up as follows:
BT_UUID_SPD_SERVICE is our custom 128-bit UUID...
Hi.
We moved to version 2.5.2. Here we encounter some problem with data mode. Sometimes we don't get response of exit from data mode.
We publish data, after we send "...
Hello Everyone,
I wanted to ask if there is a way to use SonarCloud for analyzing a firmware based on the nordic toolchain v2.5.2, I understood that I have to set up the...
The MDS service supports the chunks through Bluetooth GW. in reality this is not of much use in real scenario. So is it possible to upload the chunks directly to memfault...
Hi,
We are having trouble configuring our PDM peripheral to operate at 48 kHz. THe nRF5340-specific documentation on the PDM module has equations suggesting that 48 kHZ...
I am running the demo of "nrf-knx-iot/samples/light_switch_actuator" on my customized board based on NRF52840.
I could burn the light_switch_actuator firmware into this...
I posted my configuration in a separate discussion .
Calling this method works when CONFIG_BOOTLOADER_MCUBOOT=n works. But as soon as we flash an image with MCUBoot enabled...