Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
It isn't clear from the nRF5340 documentation and the only related post doesn't answer it but if we want +3 dBm output power, do we need to wire the nRF5340 in high voltage...
I have a mouse that is advertising, and I paired it with my host. It always stays in connected mode. When I press the three buttons — middle, left, and right — for 5 seconds...
What is the recommended termination for unused RF pins on the nRF54L15 in QFN48 (QFAA) package? Can you confirm this is acceptable?
ANT Pin 31, floating VSS_PA Pin 32, grounded...
Hi, I want to change the voltage of the VDDIO in the group of pins labelled Port 1. I launched Board Configurator from nRF Connect for Desktop but it says "This development...
I have code set up to configure Timer3 to generate a Compare event at 100 KHz, using the PPI so that triggers an ADC Sample event for the two enabled ADC channels. EasyDMA...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hi,
I'm developing an application with a custom firmware image for both the nRF52840 and nRF9160 on the nRF9160DK. I've always been on ncs v2.5.0 and decided it would...
Hello,
I am trying to program a custom device of nrf54l15 using nrf connect for desktop app(V5.2.0) -> Programmer(V4.6.2)
I am able to program it but this is how I see...
I am bringing up a custom board using the nRF54L15 (Fanstel BM15M module) and I am using SPIM00 as the high-speed SPI interface. I am configuring the peripheral through Zephyr...
Using PPK to measure the current, it was found that there was a 1-minute cycle signal in the current waveform. No timer was set. The watchdog timer is 10 seconds.
Im currently working on a project which should receive audio through CIS and retransmit it over BIS. Im using nrf5340_audio_dk for this. Ive tried using https://docs.nordicsemi...
Hi,
We came across this feature " PLMN selection optimization during initial search ", enabled by AT%FEACONF=0,3,1 . It sounds good for speed and power consumption.
...
Hi all,
I’m working on a custom board based on the nRF9151 , and using the Ignion NN03‑320 antenna for GNSS reception.
In our GNSS TTFF testing (using AT commands),...
I'm developing a keyless entry/start system for vehicles with the following requirements:
The vehicle side uses an nRF54L15, while the mobile phone is a standard smartphone...
