Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
Hi All!
I tested the central & peripheral_hr_coded examples.By using Nrf connect sdk version 2.0.0 /2.0.2 ,nrf52833DK's. Is it possible to add a feature in the example that...
I am working on implementing a BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED advertising setup.
I would like to minimize the current spike transients...
Hi Team We are working on NFC for our new product. When we measure the power level each GPIO we don't reach more than 700mv. Changing the antenna to a larger antenna did not...
Hello,
I have enabled NRF_LOG over RTT but I get flooded by the same message until my application crashed.
For example:
I get continuously:
what am I doing...
Hello List,
First some context: I am working with SDK 17.1.0 on a nrf52840 (arduino nano ble).
Created a variant of the ble_app_uart example and want to add pairing/bonding...
Hi,
I am aware, that I the PDK is deprecated and I plan to use a nRF5340-DK in the near future.
However, I would like to make use of the PDK I have sitting around and...
Dear Mate,
I am trying to build and flash a program by using (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com...
Dear all,
I'm using nRF52832 and using timers to turn on/off GPIOs.
I saw that timer0, 1 and 2 has 4 CC registers.
Right now, I'm using timer0 like this:
1) turn...
Hi team,
I have some doubts regarding mcuboot behavior on firmware failure.
1) Consider the situation I have flashed a new image , it will get validate before mcuboot...
Hi,
I'm trying to use XIP on our custom board running a nrf5340 with a different Flash memory than the one on the nrf5340-devkit.
The XIP worked on nrf5340dk, but now...
Hi,
I have an nRF9160 device which is going thru PTCRB cert. We are doing TRP/TIS and nRF9160 won't connect to the Anritsu MT8821C. Basically it tries to connect and just...
I have a working MQTT subscription list, when I add a new topic for subscription my subscribe fails with ENOMEM error -12.
If I remove another topic, I can add new topics...
I am looking for a way to set the TX power in Openthtread using Matter with the current version of the nRF-SDK. It appears I cannot find a solution which is up to date.
Hello, guys.
We are using nRF51822 SoC together with nRF5 v12.3.0 SDK.
According to the nRF51822 memory layout , half of the 256KB flash memory space is taken by the Softdevice...
I am using an Nrf52840 and sdk V14.2.0.
My question is how to compute the battery voltage based on my hardware.
The hardware uses AIN0 to measure.
The hardware has a...
