HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
I want change toolchains, so when i open nrfconnect terminal I can use my own west command. I've read link , link and link
Option in the picture lets me install or open...
Hi,
There were GPIO /SPI Interface headers are given on NRF21540 EK .now how we can connect RF input to TRX pin of NRF21540.
please provide the Understanding of RF input...
Hi
We are looking into connecting an external GNSS antenna to the Thingy91x board. The drawings metion 2 ports J1 and J2 but can't find anything in the docs if these are...
Hi, I am currently outputting some audio (1000hz sine wave) via audio_i2s_blk_comp_cb_register and audio_i2s_set_next_buf (from audio_i2s.h ) through the line out audio jack...
Good morning, I am trying to send data via BLE from a custom board (with the nRF52840 microcontroller) that has sensors, to an evaluation board nRF52840 PCA10056. To do this...
Hello Team,
Please help in guiding to enable L4 security & detailed guide to enable L4 in latest nRF Connect SDK having nRF54L15 chipset on nRF connect SDK 2.7.0
Thank...
Hi there,
I have a small custom board with the nRF52810 that uses the LDO instead of the DC-DC, it also doesn't have the 32KHz LF crystal.
Was able to add this to the...
hi destiny98 i also working on sending string from peripheral to central but central device not able to receive it and show the same message every time, here i attach code...
Hi,
I'm trying to retrieve the MCUBoot version inside my application (from the VERSION file).
In the Zephyr documentation ( docs.zephyrproject.org/.../index.html) , I...
sample example zephyr/samples/hello_world build & flash successfully in nrf connect sdk v2.9.0 but logs not printing using UART & RTT
same code zephyr/samples/hello_world...
I'm testing the spi communication protocol with the nRF54L15 DK. At that moment, I'm testing the lesson5-exercise 1 solution of the intermediate course. The problem appears...
Dear all,
I've tried to build the central_hr sample using c:/ncs/v2.9.0/zephyr/samples//bluetooth/hci_ipc for the cpunet. The SDK version is v2.9.0 and the board is nrf5340dk...
Hi,
We have a pretty small device to be designed and I was wondering if nRF54L15 CAAA WLCSP would
have updated recommendations for matching network components available...
