Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi all,
I am using segger studio , i am trying to run examples of mesh alpha sdk that nordic provides. I can able to dump the code on board successfully. But if i try to...
I am using the nrf_i2s driver, and it works properly ... with CONFIG.CHANNELS set to stereo.
But for my application, I only need to drive data onto SDOUT left channel. ...
Dear sir please help..its urgent.
i am using below configurations. Nordic - nRF52832-QFAA-B Soft device - 132 SDK - nRF5_SDK_14.2
I am following the "ble_app_att_mtu_throughput...
Hi all,
I am using the nRF51822 BLE with custom board, I want to configure Timer1 to generate IRQ for every 1ms and Timer2 to generate IRQ for every 1us. I want to run...
Hi,
I want to change the UART0 baud rate at runtime (the peripheral has switched to a new rate). Is it enough to reset to (say) 9600 baud, like:
NRF_UART0->BAUDRATE =...
Hello,
I am using the nRF52840 DK with Keil to develop. I have a structure defined as follows:
I have verified that uint8 is 1 byte, uint16 is 2 bytes, and uint32 is...
Hi,
I am using nRF52832 Dk and SD132, sdk is 13.1. I have sent my sensor data to server using external wifi module which is interface with nRF52832 DK.
Everything working...
I have a Client and two Server, so i did flash the example code.
But, from the command '3', i get an error that i do not know.
Can you help me ?
What is correct value...
Hi.
I want to add constant descriptor. Can I save the memory using const variable and BLE_GATTS_VLOC_USER. Will it occur some faults in future?
static const uint8_t value...
I am developing a program with BMI160 with this libraries , but I do not know to which it refers the following code at line 5 and 6: sensor.read and sensor.write.
It is...
I’m using the example “light switch” of SDK Mesh.1.0.1. In my case, i use nrf51 dk as client and three nrf51 dongles as servers but It doesn’t work.
I have tried to debug...
Hi everyone! I'm trying to generate a modulated continuous signal in a specific channel using nrf52832. I used a code made from radio_test example that follows. The problem...
when i program the code firstly , the device is not broadcast,But the other is running well. the output log is correctly.
when i reset the device several times , the device...
Hi, I have done some developing for nRF51822 with Keil before and now I have started out with a new project using Segger so of course I wanted to use the lastest SDK with...
While writing a hardware (I2S) assisted software UART I have noticed that the SDK 14.2 seems to be missing two enums for 32MDIV30 and 32MDIV32
Below is a diff from my private...
